We assume VLENB is a multiple of 8 and previously relied on shift
pairs being optimized to an AND+SHL/SHR and computeKnownBits
removing the AND. This doesn't happen if (vlenb >> 3) gets CSEd
to have multiple uses. This patch manually emits the best shift
to workaround this.
In most of cases, it has a single space after comma in assembly operands.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D103790
We aren't going to connect the result to anything so we might
as well avoid allocating a register.
Reviewed By: frasercrmck, HsiangKai
Differential Revision: https://reviews.llvm.org/D102031
RV32 is able to use the llvm.experimental.vector.insert intrinsics too.
This patch ensures they're tested.
Reviewed By: khchen, asb
Differential Revision: https://reviews.llvm.org/D99655
This patch addresses a few issues when dealing with scalable-vector
INSERT_SUBVECTOR and EXTRACT_SUBVECTOR nodes.
When legalizing in DAGTypeLegalizer::SplitVecRes_INSERT_SUBVECTOR, we
store the low and high halves to the stack separately. The offset for
the high half was calculated incorrectly.
Additionally, we can optimize this process when we can detect that the
subvector is contained entirely within the low/high split vector type.
While this optimization is valid on scalable vectors, when performing
the 'high' optimization, the subvector must also be a scalable vector.
Note that the 'low' optimization is still conservative: it may be
possible to insert v2i32 into the low half of a split nxv1i32/nxv1i32,
but we can't guarantee it. It is always possible to insert v2i32 into
nxv2i32 or v2i32 into nxv4i32+2 as we know vscale is at least 1.
Lastly, in SelectionDAG::isSplatValue, we early-exit on the extracted subvector value
type being a scalable vector, forgetting that we can also extract a
fixed-length vector from a scalable one.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D98495
Like with EXTRACT_SUBVECTOR, INSERT_SUBVECTOR poses a problem
for vector masks as RVV isn't able to slide mask types around. We choose
instead to bitcast to equivalently-sized i8 types where we can, else we
zero-extend, perform the operation, and truncate back down.
One test was left disabled due to a crash in the legalizer.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D97559
This patch fixes a bug where the lowering for INSERT_SUBVECTOR and
EXTRACT_SUBVECTOR would insist on first extracting a register-aligned
LMUL1 vector type before perfoming the slide up/down. This was even if
the vector was a fractional LMUL type, in which case the aligned
EXTRACT_SUBVECTOR was invalid.
This issue only occurred for scalable vector types, but a variety of
tests for both scalable and fixed-length vectors have been added to
ensure this does not regress in the future.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D97556
This patch extends the support for RVV INSERT_SUBVECTOR to cover those
which don't align to a vector register boundary. Like the support for
EXTRACT_SUBVECTOR in D96959, it accomplishes this by extracting the
nearest register-sized subvector (a subregister operation), then sliding
the vector down with VSLIDEDOWN, inserting the subvector to the first
position, and sliding the vector back up again afterwards.
Unlike subvector extraction, for vectors that occupy less than a full
vector register we must preserve the untouched elements. We do this by
lowering to an LMUL=1 INSERT_SUBVECTOR using the above method and
lowering that to a VSLIDEUP with a zero offset. This uses a
tail-undisturbed policy and so has the effect of "sliding in" the
subvector elements while preserving the surrounding ones.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D96972
This patch adds support for INSERT_SUBVECTOR and EXTRACT_SUBVECTOR
(nominally where both operands are scalable vector types) where the
vector, subvector, and index align sufficiently to allow decomposition
to subregister manipulation:
* For extracts, the extracted subvector must correctly align with the
lower elements of a vector register.
* For inserts, the inserted subvector must be at least one full vector
register, and correctly align as above.
This approach should work for fixed-length vector insertion/extraction
too, but that will come later.
Reviewed By: craig.topper, khchen, arcbbb
Differential Revision: https://reviews.llvm.org/D96873
Craig Topper