ARM prologues usually look like:
push {r7, lr}
sub sp, sp, #4
If code size is extremely important, this can be optimised to the single
instruction:
push {r6, r7, lr}
where we don't actually care about the contents of r6, but pushing it subtracts
4 from sp as a side effect.
This should implement such a conversion, predicated on the "minsize" function
attribute (-Oz) since I've yet to find any code it actually makes faster.
llvm-svn: 194264
Cortex-M0 supports these 32-bit instructions despite being Thumb1 only
(mostly). We knew about that but not that the aliases without the default "sy"
operand were also permitted.
llvm-svn: 194094
ResolveFrameIndex had what appeared to be a very nasty hack for when the
frame-index referred to a callee-saved register. In this case it "adjusted" the
offset so that the address was correct if (and only if) the MachineInstr
immediately followed the respective push.
This "worked" for all forms of GPR & DPR but was only ever used to set the
frame pointer itself, and once this was put in a more sensible location the
entire state-tracking machinery it relied on became redundant. So I stripped
it.
The only wrinkle is that "add r7, sp, #0" might theoretically be slower (need
an actual ALU slot) compared to "mov r7, sp" so I added a micro-optimisation
that also makes emitARMRegUpdate and emitT2RegUpdate also work when NumBytes ==
0.
No test changes since there shouldn't be any functionality change.
llvm-svn: 194025
Add a Virtualization ARM subtarget feature along with adding proper build
attribute emission for Tag_Virtualization_use (encodes Virtualization and
TrustZone) and Tag_MPextension_use.
Also rework test/CodeGen/ARM/2010-10-19-mc-elf-objheader.ll testcase to
something that is more maintainable. This changes the focus of this
testcase away from testing CPU defaults (which is tested elsewhere), onto
specifically testing that attributes are encoded correctly.
llvm-svn: 193859
Fix Tag_ABI_HardFP_use build attribute to handle single precision FP,
replace deprecated Tag_ABI_HardFP_use value of 3 with 0 and also add
some tests for Tag_ABI_VFP_args.
llvm-svn: 193856
When an extend more than doubles the size of the elements (e.g., a zext
from v16i8 to v16i32), the normal legalization method of splitting the
vectors will run into problems as by the time the destination vector is
legal, the source vector is illegal. The end result is the operation
often becoming scalarized, with the typical horrible performance. For
example, on x86_64, the simple input of:
define void @bar(<16 x i8> %a, <16 x i32>* %p) nounwind {
%tmp = zext <16 x i8> %a to <16 x i32>
store <16 x i32> %tmp, <16 x i32>*%p
ret void
}
Generates:
.section __TEXT,__text,regular,pure_instructions
.section __TEXT,__const
.align 5
LCPI0_0:
.long 255 ## 0xff
.long 255 ## 0xff
.long 255 ## 0xff
.long 255 ## 0xff
.long 255 ## 0xff
.long 255 ## 0xff
.long 255 ## 0xff
.long 255 ## 0xff
.section __TEXT,__text,regular,pure_instructions
.globl _bar
.align 4, 0x90
_bar:
vpunpckhbw %xmm0, %xmm0, %xmm1
vpunpckhwd %xmm0, %xmm1, %xmm2
vpmovzxwd %xmm1, %xmm1
vinsertf128 $1, %xmm2, %ymm1, %ymm1
vmovaps LCPI0_0(%rip), %ymm2
vandps %ymm2, %ymm1, %ymm1
vpmovzxbw %xmm0, %xmm3
vpunpckhwd %xmm0, %xmm3, %xmm3
vpmovzxbd %xmm0, %xmm0
vinsertf128 $1, %xmm3, %ymm0, %ymm0
vandps %ymm2, %ymm0, %ymm0
vmovaps %ymm0, (%rdi)
vmovaps %ymm1, 32(%rdi)
vzeroupper
ret
So instead we can check if there are legal types that enable us to split
more cleverly when the input vector is already legal such that we don't
turn it into an illegal type. If the extend is such that it's more than
doubling the size of the input we check if
- the number of vector elements is even,
- the source type is legal,
- the type of a split source is illegal,
- the type of an extended (by doubling element size) source is legal, and
- the type of that extended source when split is legal.
If the conditions are met, instead of just splitting both the
destination and the source types, we create an extend that only goes up
one "step" (doubling the element width), and the continue legalizing the
rest of the operation normally. The result is that this operates as a
new, more effecient, termination condition for the loop of "split the
operation until the destination type is legal."
With this change, the above example now compiles to:
_bar:
vpxor %xmm1, %xmm1, %xmm1
vpunpcklbw %xmm1, %xmm0, %xmm2
vpunpckhwd %xmm1, %xmm2, %xmm3
vpunpcklwd %xmm1, %xmm2, %xmm2
vinsertf128 $1, %xmm3, %ymm2, %ymm2
vpunpckhbw %xmm1, %xmm0, %xmm0
vpunpckhwd %xmm1, %xmm0, %xmm3
vpunpcklwd %xmm1, %xmm0, %xmm0
vinsertf128 $1, %xmm3, %ymm0, %ymm0
vmovaps %ymm0, 32(%rdi)
vmovaps %ymm2, (%rdi)
vzeroupper
ret
This generalizes a custom lowering that was added a while back to the
ARM backend. That lowering is no longer necessary, and is removed. The
testcases for it, however, provide excellent ARM tests for this change
and so remain.
rdar://14735100
llvm-svn: 193727
Helper functions are added:
emitPostLd: emit a post-increment load operation with given size.
emitPostSt: emit a post-increment store operation with given size.
No functionality change.
llvm-svn: 193656
Adds a subtarget feature for the CRC instructions (optional in v8-A) to the ARM (32-bit) backend.
Differential Revision: http://llvm-reviews.chandlerc.com/D2036
llvm-svn: 193599
By vectorizing a series of srl, or, ... instructions we have obfuscated the
intention so much that the backend does not know how to fold this code away.
radar://15336950
llvm-svn: 193573
an MCExpr, in order to avoid writing an encoded zero value in the immediate
field.
When getUnconditionalBranchTargetOpValue is called with an MCExpr target, we
don't know what the final immediate field value should be. We shouldn't
explicitly set the immediate field to an encoded zero value as zero is encoded
with a non-zero bit pattern. This leads to bits being set that pollute the
final immediate value. The nature of the encoding is such that the polluted
bits only affect very large immediate values, explaining why this hasn't
caused problems earlier.
Fixes <rdar://problem/15155975>.
llvm-svn: 193535
This commit allows the ARM integrated assembler to parse
and assemble the code with .eabi_attribute, .cpu, and
.fpu directives.
To implement the feature, this commit moves the code from
AttrEmitter to ARMTargetStreamers, and several new test
cases related to cortex-m4, cortex-r5, and cortex-a15 are
added.
Besides, this commit also change the Subtarget->isFPOnlySP()
to Subtarget->hasD16() to match the usage of .fpu directive.
This commit changes the test cases:
* Several .eabi_attribute directives in
2010-09-29-mc-asm-header-test.ll are removed because the .fpu
directive already cover the functionality.
* In the Cortex-A15 test case, the value for
Tag_Advanced_SIMD_arch has be changed from 1 to 2,
which is more precise.
llvm-svn: 193524
When assembling, a .thumb_func directive is supposed to be applicable to the
next symbol definition, even if there are intervening directives. We were
racing ahead to try and find it, and this commit should fix the issue.
Patch by Gabor Ballabas
llvm-svn: 193403
There's a barrier instruction so that should still be used, but most actual
atomic operations are going to need a platform decision on the correct
behaviour (either nop if single-threaded or OS-support otherwise).
rdar://problem/15287210
llvm-svn: 193399
This commit changes the struct byval lowering for arm to use inline
checks for the subtarget instead of a class abstraction to represent
the differences. The class abstraction was judged to be too much
code for this task.
No intended functionality change.
llvm-svn: 193357
This prevents us from silently accepting invalid instructions on (for example)
Cortex-M4 with just single-precision VFP support.
No tests for the extra Pat Requires because they're essentially assertions: the
affected code should have been lowered to libcalls before ISel.
rdar://problem/15302004
llvm-svn: 193354
The fused multiply instructions were added in VFPv4 but are still NEON
instructions, in particular they shouldn't be available on a Cortex-M4 not
matter how floaty it is.
llvm-svn: 193342
If an alias inherits directly from InstAlias then it doesn't get any default
"Requires" values, so llvm-mc will allow it even on architectures that don't
support the underlying instruction.
This tidies up the obvious VFP and NEON cases I found.
llvm-svn: 193340
The compiler-rt functions __adddf3vfp and so on exist purely to allow Thumb1
code to make use of VFP instructions by switching back to ARM mode, they make
no sense for M-class processors which don't even have an ARM mode.
Given that justification, in practice this is a platform ABI decision so the
actual check is based on that rather than CPU features.
rdar://problem/15302004
llvm-svn: 193327
POP instructions are aliased to the ARM LDM variants but have different syntax.
This caused two problems: we tried to access a non-existent operand to annotate
the '!', and the error message didn't make much sense.
With some vigorous hand-waving in the error message both problems can be
fixed.
llvm-svn: 193322
The set of circumstances where the writeback register is allowed to be in the
list of registers is rather baroque, but I think this implements them all on
the assembly parsing side.
For disassembly, we still warn about an ARM-mode LDM even if the architecture
revision is < v7 (the required architecture information isn't available). It's
a silly instruction anyway, so hopefully no-one will mind.
rdar://problem/15223374
llvm-svn: 193185
This commit implements the correct lowering of the
COPY_STRUCT_BYVAL_I32 pseudo-instruction for thumb1 targets.
Previously, the lowering of COPY_STRUCT_BYVAL_I32 generated the
post-increment forms of ldr/ldrh/ldrb instructions. Thumb1 does not
have the post-increment form of these instructions so the generated
assembly contained invalid instructions.
Passing the generated assembly to gcc caused it to complain with an
error like this:
Error: cannot honor width suffix -- `ldrb r3,[r0],#1'
and the integrated assembler would generate an object file with an
invalid instruction encoding.
This commit contains a small test case that demonstrates the problem
with thumb1 targets as well as an expanded test case that more
throughly tests the lowering of byval struct passing for arm,
thumb1, and thumb2 targets.
llvm-svn: 192916
This commit refactors the lowering of the COPY_STRUCT_BYVAL_I32
pseudo-instruction in the ARM backend. We introduce a new helper
class that encapsulates all of the operations needed during the
lowering. The operations are implemented for each subtarget in
different subclasses. Currently only arm and thumb2 subtargets are
supported.
This refactoring was done to easily implement support for thumb1
subtargets. This initial patch does not add support for thumb1, but
is only a refactoring. A follow on patch will implement the support
for thumb1 subtargets.
No intended functionality change.
llvm-svn: 192915
When we had a sequence like:
s1 = VLDRS [r0, 1], Q0<imp-def>
s3 = VLDRS [r0, 2], Q0<imp-use,kill>, Q0<imp-def>
s0 = VLDRS [r0, 0], Q0<imp-use,kill>, Q0<imp-def>
s2 = VLDRS [r0, 4], Q0<imp-use,kill>, Q0<imp-def>
we were gathering the {s0, s1} loads below the s3 load. This is fine,
but confused the verifier since now the s3 load had Q0<imp-use> with
no definition above it.
This should mark such uses <undef> as well. The liveness structure at
the beginning and end of the block is unaffected, and the true sN
definitions should prevent any dodgy reorderings being introduced
elsewhere.
rdar://problem/15124449
llvm-svn: 192344
This patch fixes an old FIXME by creating a MCTargetStreamer interface
and moving the target specific functions for ARM, Mips and PPC to it.
The ARM streamer is still declared in a common place because it is
used from lib/CodeGen/ARMException.cpp, but the Mips and PPC are
completely hidden in the corresponding Target directories.
I will send an email to llvmdev with instructions on how to use this.
llvm-svn: 192181
from struct byval to registers.
We used to pass 0 which means the alignment of PtrVT. Even when the alignment
of the struct is smaller than 4, the LOADs would have alignment of 4, and
further optimizations could combine the LOADs into a ldm, which would
cause crash.
The fix is to pass the alignment of the struct byval.
rdar://problem/15144402
llvm-svn: 192126
The hint instructions ("nop", "yield", etc) are mostly Thumb2-only, but have
been ported across to the v6M architecture. Fortunately, v6M seems to sit
nicely between v6 (thumb-1 only) and v6T2, so we can add a feature for it
fairly easily.
rdar://problem/15144406
llvm-svn: 192097
When MC was first added, targets could use hasRawTextSupport to keep features
working before they were added to the MC interface.
The design goal of MC is to provide an uniform api for printing assembly and
object files. Short of relaxations and other corner cases, a object file is
just another representation of the assembly.
It was never the intention that targets would keep doing things like
if (hasRawTextSupport())
Set flags in one way.
else
Set flags in another way.
When they do that they create two code paths and the object file is no longer
just another representation of the assembly. This also then requires testing
with llc -filetype=obj, which is extremelly brittle.
This patch removes some of these hacks by replacing them with smaller ones.
The ARM flag setting is trivial, so I just moved it to the constructor. For
Mips, the patch adds two temporary hack directives that allow the assembly
to represent the same things as the object file was already able to.
The hope is that the mips developers will replace the hack directives with
the same ones that gas uses and drop the -print-hack-directives flag.
I will also try to implement a target streamer interface, so that we can
move this out of the common code.
In summary, for any new work, two rules of the thumb are
* Don't use "llc -filetype=obj" in tests.
* Don't add calls to hasRawTextSupport.
llvm-svn: 192035
optimizeSelect folds (predicated) copy instructions, it must not ignore
the original register class of the operand when replacing the register
with the copies dest register.
llvm-svn: 191963
The jump doesn't really kill the registers, the following call does but
we never get back anyway.
This avoids some verify-machineinstrs problems when TAILJUMPs are
if-converted.
llvm-svn: 191962
This function-attribute modifies the callee-saved register list and function
epilogue (specifically the return instruction) so that a routine is suitable
for use as an interrupt-handler of the specified type without disrupting
user-mode applications.
rdar://problem/14207019
llvm-svn: 191766
For targets that have instruction itineraries this means no change. Targets
that move over to the new schedule model will use be able the new schedule
module for instruction latencies in the if-converter (the logic is such that if
there is no itineary we will use the new sched model for the latencies).
Before, we queried "TTI->getInstructionLatency()" for the instruction latency
and the extra prediction cost. Now, we query the TargetSchedule abstraction for
the instruction latency and TargetInstrInfo for the extra predictation cost. The
TargetSchedule abstraction will internally call "TTI->getInstructionLatency" if
an itinerary exists, otherwise it will use the new schedule model.
ATTENTION: Out of tree targets!
(I will also send out an email later to LLVMDev)
This means, if your target implements
unsigned getInstrLatency(const InstrItineraryData *ItinData,
const MachineInstr *MI,
unsigned *PredCost);
and returns a value for "PredCost", you now also need to implement
unsigned getPredictationCost(const MachineInstr *MI);
(if your target uses the IfConversion.cpp pass)
radar://15077010
llvm-svn: 191671
As specified in A8.8.72/A8.8.73/A8.8.74 in the ARM ARM, all variants of the ARM LDRD instruction have the following two constraints:
LDRD<c> <Rt>, <Rt2>, ...
(a) Rt must be even-numbered and not r14
(b) Rt2 must be R(t+1)
If those two constraints are not met the result of executing the instruction will be unpredictable.
Constraint (b) was already enforced, this commit adds support for constraint (a).
Fixes rdar://14479793.
llvm-svn: 191520
LDRD<c> <Rt>, <Rt2>, <label>
LDRD<c> <Rt>, <Rt2>, [<Rn>{, #+/-<imm>}]
LDRD<c> <Rt>, <Rt2>, [<Rn>], #+/-<imm>
LDRD<c> <Rt>, <Rt2>, [<Rn>, #+/-<imm>]!
As specified in A8.8.72/A8.8.73 in the ARM ARM, the T1 encoding has a constraint which enforces that Rt != Rt2.
If this constraint is not met the result of executing the instruction will be unpredictable.
Fixes rdar://14479780.
llvm-svn: 191504
Generally, it is desirable to distribute (a + b) * c to a*c + b*c for
ARM with VMLx forwarding, where a, b and c are vectors.
However, for (a + b)*(a + b), distribution will result in one extra
instruction.
With distribution:
x = a + b (add)
y = a * x (mul)
z = y + b * y (mla)
Without distribution:
x = a + b (add)
z = x * x (mul)
This patch checks if a mul is a square of add/sub. If yes, skip
distribution.
llvm-svn: 191410
This is being disabled because it is no longer needed for
performance. It is only used by postRAscheduler which is also planned
for removal, and it is implemented with an out-dated view of register
liveness. It consideres aliases instead of register units, assumes
valid kill flags, and assumes implicit uses on partial register
defs. Kill flags and implicit operands are error prone and impossible
to verify. We should gradually eliminate dependence on them in the
postRA phases.
Targets that still benefit from this should move to the MI
scheduler. If that doesn't solve the problem, then we should add a
hook to regalloc to optimize reload placement.
llvm-svn: 191348
Previously, the DAGISel function WalkChainUsers was spotting that it
had entered already-selected territory by whether a node was a
MachineNode (amongst other things). Since it's fairly common practice
to insert MachineNodes during ISelLowering, this was not the correct
check.
Looking around, it seems that other nodes get their NodeId set to -1
upon selection, so this makes sure the same thing happens to all
MachineNodes and uses that characteristic to determine whether we
should stop looking for a loop during selection.
This should fix PR15840.
llvm-svn: 191165
The 'Deprecated' class allows you to specify a SubtargetFeature that the
instruction is deprecated on.
The 'ComplexDeprecationPredicate' class allows you to define a custom
predicate that is called to check for deprecation.
For example:
ComplexDeprecationPredicate<"MCR">
would mean you would have to define the following function:
bool getMCRDeprecationInfo(MCInst &MI, MCSubtargetInfo &STI,
std::string &Info)
Which returns 'false' for not deprecated, and 'true' for deprecated
and store the warning message in 'Info'.
The MCTargetAsmParser constructor was chaned to take an extra argument of
the MCInstrInfo class, so out-of-tree targets will need to be changed.
llvm-svn: 190598
We were figuring out whether to use tPICADD or PICADD, then just using
tPICADD unconditionally anyway. Oops.
A testcase from someone familiar enough with ELF to produce one would
be appreciated. The existing PIC testcase correctly verifies the .s
generated, but that doesn't catch this bug, which only showed up in
direct-to-object mode.
http://llvm.org/bugs/show_bug.cgi?id=17180
llvm-svn: 190417
We used to generate the compact unwind encoding from the machine
instructions. However, this had the problem that if the user used `-save-temps'
or compiled their hand-written `.s' file (with CFI directives), we wouldn't
generate the compact unwind encoding.
Move the algorithm that generates the compact unwind encoding into the
MCAsmBackend. This way we can generate the encoding whether the code is from a
`.ll' or `.s' file.
<rdar://problem/13623355>
llvm-svn: 190290
These were pretty straightforward instructions, with some assembly support
required for HLT.
The ARM assembler is keen to split the instruction mnemonic into a
(non-existent) 'H' instruction with the LT condition code. An exception for
HLT is needed.
HLT follows the same rules as BKPT when in IT blocks, so the special BKPT
hadling code has been adapted to handle HLT also.
Regression tests added including diagnostic tests for out of range immediates
and illegal condition codes, as well as negative tests for pre-ARMv8.
llvm-svn: 190053
Solution is not sufficient to prevent 'mov pc, lr' being emitted for jump table code.
Test case doesn't trigger the added functionality.
llvm-svn: 190047
This improves code generation for jump tables by avoiding the emission of "mov pc, lr" which could fool the processor into believing this is a return from a function causing mispredicts. The code generation logic for jump tables uses ADR to materialize the address of the jump target.
Patch by Daniel Stewart!
llvm-svn: 190043
These instructions, such as vmul.f32, require the second source operand to
be in D0-D15 rather than the full D0-D31. When optimizing, make sure to
account for that by constraining the register class of a replacement virtual
register to be compatible with the virtual register(s) it's replacing.
I've been unsuccessful in creating a non-fragile regression test. This issue
was detected by the LLVM nightly test suite running on an A15 (Bullet).
PR17093: http://llvm.org/bugs/show_bug.cgi?id=17093
llvm-svn: 189972
This reverts commit r189648.
Fixes for the previously failing clang-side arm_neon_intrinsics test
cases will be checked in separately.
llvm-svn: 189841
What we really want is to enable Swift by default for *v7s triples (and there already seems to be some logic which attempts to do that). In that case the iOS version doesn't matter.
llvm-svn: 189763
In addition to recognizing when the multiply's second argument is
coming from an explicit VDUPLANE, also look for a plain scalar
f32 reference and reference it via the corresponding vector
lane.
rdar://14870054
llvm-svn: 189619
Fix a few things in one swoop.
# Add some negative tests.
# Fix some formatting issues.
# Add some missing IsThumb / ARMv8
# Fix some outs / ins mistakes.
llvm-svn: 189490
The usual default of "dmb ish" (inner-shareable) isn't even a valid instruction
on v6M or v7M (well, it does the same thing but software is strongly
discouraged from using it) so we should emit a full-system barrier there.
llvm-svn: 189483
The vqdmlal and vqdmlls instructions are really just a fused pair consisting of
a vqdmull.sN and a vqadd.sN. This adds patterns to LLVM so that we can switch
Clang's CodeGen over to generating these instead of the special vqdmlal
intrinsics.
llvm-svn: 189480
These instructions aren't particularly complicated and it's well worth having
patterns for some reasonably useful LLVM IR that will match them. Soon we
should be able to switch Clang over to producing this natural version.
llvm-svn: 189335
Get the register class right for the TST instruction. This keeps the
machine verifier happy, enabling us to turn it on for another test.
rdar://12594152
llvm-svn: 189274
The create machine code wasn't properly in SSA, which the machine verifier
properly complains about. Now that fast-isel is closer to verifier clean,
errors like this show up more clearly.
Additionally, the Thumb pseudo tPICADD was used for both ARM and Thumb
mode functions, which is obviously wrong. Fix that along the way.
Test case is part of the following commit which will finish making an
additional fast-isel test verifier clean an enable it for the
regression test suite. This commit is separate since its not just
a verifier cleanup, but an actual correctness issue.
rdar://12594152 (for the fast-isel verifier aspects)
llvm-svn: 189269
I'd forgotten that "Requires" blocks override rather than add to the
constraints, so my pseudo-instruction was being selected in Thumb mode leading
to nonsense instructions.
rdar://problem/14817358
llvm-svn: 189096
The instruction to convert between floating point and fixed point representations
takes an immediate operand for the number of fractional bits of the fixed point
value. ARMARM specifies that when that number of bits is zero, the assembler
should encode floating point/integer conversion instructions.
This patch adds the necessary instruction aliases to achieve this behaviour.
llvm-svn: 189009
Back in the mists of time (2008), it seems TableGen couldn't handle the
patterns necessary to match ARM's CMOV node that we convert select operations
to, so we wrote a lot of fairly hairy C++ to do it for us.
TableGen can deal with it now: there were a few minor differences to CodeGen
(see tests), but nothing obviously worse that I could see, so we should
probably address anything that *does* come up in a localised manner.
llvm-svn: 188995
According to the ARM specification, "mov" is a valid mnemonic for all Thumb2 MOV encodings.
To achieve this, the patch adds one instruction alias with a special range condition to avoid collision with the Thumb1 MOV.
llvm-svn: 188901
Update testcase to be more careful about checking register
values. While regexes are general goodness for these sorts of
testcases, in this example, the registers are constrained by
the calling convention, so we can and should check their
explicit values.
rdar://14779513
llvm-svn: 188819
Previously we used a const-pool load for virtually all 64-bit floating values.
Actually, we can get quite a few common values (including 0.0, 1.0) via "vmov"
instructions of one stripe or another.
llvm-svn: 188773
The Thumb2 add immediate is in fact defined for SP. The manual is misleading as it points to a different section for add immediate with SP, however the encoding is the same as for add immediate with register only with the SP operand hard coded. As such add immediate with SP and add immediate with register can safely be treated as the same instruction.
All the patch does is adjust a register constraint on an instruction alias.
llvm-svn: 188676
When patching inlineasm nodes to use GPRPair for 64-bit values, we
were dropping the information that two operands were tied, which
effectively broke the live-interval of vregs affected.
llvm-svn: 188643
Properly constrain the operand register class for instructions used
in [sz]ext expansion. Update more tests to use the verifier now that
we're getting the register classes correct.
rdar://12594152
llvm-svn: 188594
Teach the generic instruction selection helper functions to constrain
the register classes of their input operands. For non-physical register
references, the generic code needs to be careful not to mess that up
when replacing references to result registers. As the comment indicates
for MachineRegisterInfo::replaceRegWith(), it's important to call
constrainRegClass() first.
rdar://12594152
llvm-svn: 188593
Lots of machine verifier errors result from using a plain GPR regclass
for incoming argument copies. A more restrictive rGPR class is more
appropriate since it more accurately represents what's happening, plus
it lines up better with isel later on so the verifier is happier.
Reduces the number of ARM fast-isel tests not running with the verifier
enabled by over half.
rdar://12594152
llvm-svn: 188592
This unbreaks PIC with fast isel on ELF targets (PR16717). The output matches
what GCC and SDag do for PIC but may not cover all of the many flavors of PIC
that exist.
llvm-svn: 188551
Thumb2 literal loads use an offset encoding which allows for
negative zero. This fixes parsing and encoding so that #-0
is correctly processed. The parser represents #-0 as INT32_MIN.
llvm-svn: 188549
There are many Thumb instructions which take 12-bit immediates encoded in a special
8-byte value + 4-byte rotator form. Not all numbers are represented, and it's legal
to transform an assembly instruction to be able to encode the immediate.
For example: AND and BIC are complementary instructions; one can switch the AND
to a BIC as long as the immediate is complemented.
The intent is to switch one instruction into its complementary one when the immediate
cannot be encoded in the form requested in the original assembly and when the
complementary immediate is encodable.
The patch addresses two issues:
1. definition of t2SOImmNot immediate - it has to check that the orignal value is
not encoded naturally
2. t2AND and t2BIC instruction aliases which should use the Thumb2 SOImm operand
rather than the ARM one.
llvm-svn: 188548
Before this patch this flag is IOS specific, but is also
useful for bare project like bootloaders / kernels etc,
since movw / movt prevents simple relocation. Therefore
make this flag more commonly available.
note: this patch depends on a similiar rename in clang
Patch by Jeroen Hofstee.
llvm-svn: 188487
r9 is defined as a platform-specific register in the ARM EABI.
It can be reserved for a special purpose or be used as a general
purpose register. Add support for reserving r9 for all ARM, while
leaving the IOS usage unchanged.
Patch by Jeroen Hofstee.
llvm-svn: 188485
1. The offset range for Thumb1 PC relative loads is [0..1020] and not [-1024..1020]
2. Thumb2 PC relative loads may define the PC, so the restriction placed on target register is removed
3. Removes unneeded alias between "ldr.n" and t1LDRpci. ".n" is actually stripped by both tablegen
and the ASM parser, so this alias rule really does nothing
llvm-svn: 188466
When determining if two different loads are from the same base address,
this patch allows one load to use a t2LDRi8 address mode and another to
use a t2LDRi12 address mode. The current implementation is very
conservative and this allows the case of differing Thumb2 byte loads to
be considered. Allowing these differing modes instead of forcing the exact
same opcode is useful for situations where one opcodes loads from a base
address+1 and a second opcode loads for a base address-1.
Patch by Daniel Stewart.
llvm-svn: 188385
Use it to avoid repeating ourselves too often. Also store MVT::SimpleValueType
in the TTI tables so they can be statically initialized, MVT's constructors
create bloated initialization code otherwise.
llvm-svn: 188095
In Thumb1, only one variant is supported: CPS{effect} {flags}
Thumb2 supports three:
CPS{effect}.W {flags}
CPS{effect} {flags} {mode}
CPS {mode}
Canonically, .W should be used only when ambiguity is present between encodings of different width.
The wide suffix is still accepted for the latter two forms via aliases.
llvm-svn: 188071
The long encoding for Thumb2 unconditional branches is broken.
Additionally, there is no range checking for target operands; as such
for instructions originating in assembly code, only short Thumb encodings
are generated, regardless of the bitsize needed for the offset.
Adding range checking is non trivial due to the representation of Thumb
branch instructions. There is no true difference between conditional and
unconditional branches in terms of operands and syntax - even unconditional
branches have a predicate which is expected to match that of the IT block
they are in. Yet, the encodings and the permitted size of the offset differ.
Due to this, for any mnemonic there are really 4 encodings to choose for.
The problem cannot be handled in the parser alone or by manipulating td files.
Because the parser builds first a set of match candidates and then checks them
one by one, whatever tablegen-only solution might be found will ultimately be
dependent of the parser's evaluation order. What's worse is that due to the fact
that all branches have the same syntax and the same kinds of operands, that
order is governed by the lexicographical ordering of the names of operand
classes...
To circumvent all this, any necessary disambiguation is added to the instruction
validation pass.
llvm-svn: 188067
This is the only Thumb2 instruction defined with "t" prefix; all other Thumb2 instructions have "t2" prefix (e.g. "t2CDP2" which is defined immediately afterwards).
Patch by Artyom Skrobov.
llvm-svn: 187973
Without explicit dependencies, both per-file action and in-CommonTableGen action could run in parallel.
It races to emit *.inc files simultaneously.
llvm-svn: 187780
This patch fixes the multiple breakages on ARM test-suite after the SLP
vectorizer was introduced by default on O3. The problem was an illegal
vector type on ARMTTI::getCmpSelInstrCost() <3 x i1> which is not simple.
The guard protects this code from breaking (cause of the problems) but
doesn't fix the issue that is generating the odd vector in the first
place, which also needs to be investigated.
llvm-svn: 187658
Function attributes are the future! So just query whether we want to realign the
stack directly from the function instead of through a random target options
structure.
llvm-svn: 187618
While the .td entry is nice and all, it takes a pretty gross hack in
ARMAsmParser::ParseInstruction() because of handling of other "subs"
instructions to get it to match. Ran it by Jim Grosbach and he said it was
about what he expected to make this work given the existing code.
rdar://14214063
llvm-svn: 187530
When simplifying a (or (and B A) (and C ~A)) to a (VBSL A B C) ensure that the
bitwidth of the second operands to both ands match before comparing the negation
of the values.
Split the check of the value of the second operands to the ands. Move the cast
and variable declaration slightly higher to make it slightly easier to follow.
Bug-Id: 16700
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
llvm-svn: 187404
do in the SDag when lowering references to the GOT: use
ARMConstantPoolSymbol rather than creating a dummy global variable. The
computation of the alignment still feels weird (it uses IR types and
datalayout) but it preserves the exact previous behavior. This change
fixes the memory leak of the global variable detected on the valgrind
leak checking bot.
Thanks to Benjamin Kramer for pointing me at ARMConstantPoolSymbol to
handle this use case.
llvm-svn: 187303
me) should start watching this bot more as its catching lots of bugs.
The fix here is to not construct the global if we aren't going to need
it. That's cheaper anyways, and globals have highly predictable types in
practice. I've added an assert to catch skew between our manual testing
of the type and the actual type just for paranoia's sake.
Note that this pattern is actually fine in most globals because when you
build a global with a module it automatically is moved to be owned by
that module. But here, we're in isel and don't really want to do that.
The solution of not creating a global is simpler anyways.
llvm-svn: 187302
When vectors are built from a single value, the ARM lowering issues a
scalar_to_vector node.
This node is then always morphed into a move from the general purpose unit to
the vector unit.
When the value comes from a load, this can be simplified into a vector load to
the right lane.
This patch changes the lowering of insert_vector_elt to expose a vector
friendly pattern in this situation.
This is a step toward fixing <rdar://problem/14170854>.
llvm-svn: 186999
instructions. With this patch:
1. ldr.n is recognized as mnemonic for the short encoding
2. ldr.w is recognized as menmonic for the long encoding
3. ldr will map to either short or long encodings depending on the size of the offset
llvm-svn: 186831
After Ulrich's r180677 (thanks!) TableGen is intelligent enough to
handle tied constraints involving complex operands properly, so
virtually all of the ARM custom converters are now unnecessary.
llvm-svn: 186810
indirect branches correctly. Under some circumstances, this led to the deletion
of basic blocks that were the destination of indirect branches. In that case it
left indirect branches to nowhere in the code.
This patch replaces, and is more general than either of the previous fixes for
indirect-branch-analysis issues, r181161 and r186461.
For other branches (not indirect) this refactor should have *almost* identical
behavior to the previous version. There are some corner cases where this
refactor is able to analyze blocks that the previous version could not (e.g.
this necessitated the update to thumb2-ifcvt2.ll).
<rdar://problem/14464830>
llvm-svn: 186735
My patch 'r183551 - ARM FastISel integer sext/zext improvements' was incorrect when emitting ARM register-immediate ASR, LSL, LSR instructions: they are pseudo-instructions in ARMInstrInfo.td and I should have used MOVsi instead.
This is not an issue when code is generated through a .s file, but is an issue when generated straight to a .o (-filetype=obj).
llvm-svn: 186489
block. Blocks that have an indirect branch terminator, even if it's not the
last terminator, should still be treated as unanalyzable.
<rdar://problem/14437274>
Reducing a useful regression test case is proving difficult - I hope to have
one soon.
llvm-svn: 186461
This adds an instruction alias to make the assembler recognize the alternate literal form: pli [PC, #+/-<imm>]
See A8.8.129 in the ARM ARM (DDI 0406C.b).
Fixes <rdar://problem/14403733>.
llvm-svn: 186459
We'd forgotten to provide string representations for the special ARMISD atomic
nodes; this adds them in. No effect on CodeGen, just makes the output of
"-view-whatever-dags" slightly more readable.
llvm-svn: 186406
This patch enables calls to __aeabi_idivmod when in EABI mode,
by using the remainder value returned on registers (R1),
enabled by the ARM triple "none-eabi". Note that Darwin and
GNUEABI triples will continue lowering on GNU style, that is,
using the stack for the remainder.
Still need to add SREM/UREM support fix for 64-bit lowering.
llvm-svn: 186390
ARM paired GPR COPY was being lowered to two MOVr without CC. This
patch puts the CC back.
My test is a reduction of the case where I encountered the issue,
64-bit atomics use paired GPRs.
The issue only occurs with selectionDAG, FastISel doesn't encounter it
so I didn't bother calling it.
llvm-svn: 186226
Fixes a 35% degradation compared to unvectorized code in
MiBench/automotive-susan and an equally serious regression on a private
image processing benchmark.
radar://14351991
llvm-svn: 186188
Address calculation for gather/scather in vectorized code can incur a
significant cost making vectorization unbeneficial. Add infrastructure to add
cost.
Tests and cost model for targets will be in follow-up commits.
radar://14351991
llvm-svn: 186187
Currently ARM is the only backend that supports FMA instructions (for at least some subtargets) but does not implement this virtual, so FMAs are never generated except from explicit fma intrinsic calls. Apparently this is due to the fact that it supports both fused (one rounding step) and unfused (two rounding step) multiply + add instructions. This patch clarifies that this the case without changing behavior by implementing the virtual function to simply return false, as the default TargetLoweringBase version does.
It is possible that some cpus perform the fused version faster than the unfused version and vice-versa, so the function implementation should be revisited if hard data is found.
llvm-svn: 185994
Propagate the fix from r185712 to Thumb2 codegen as well. Original
commit message applies here as well:
A "pkhtb x, x, y asr #num" uses the lower 16 bits of "y asr #num" and
packs them in the bottom half of "x". An arithmetic and logic shift are
only equivalent in this context if the shift amount is 16. We would be
shifting in ones into the bottom 16bits instead of zeros if "y" is
negative.
rdar://14338767
llvm-svn: 185982
A "pkhtb x, x, y asr #num" uses the lower 16 bits of "y asr #num" and packs them
in the bottom half of "x". An arithmetic and logic shift are only equivalent in
this context if the shift amount is 16. We would be shifting in ones into the
bottom 16bits instead of zeros if "y" is negative.
radar://14338767
llvm-svn: 185712
Tim Northover