with SUBREG_TO_REG, teach SimpleRegisterCoalescing to coalesce
SUBREG_TO_REG instructions (which are similar to INSERT_SUBREG
instructions), and teach the DAGCombiner to take advantage of this on
targets which support it. This eliminates many redundant
zero-extension operations on x86-64.
This adds a new TargetLowering hook, isZExtFree. It's similar to
isTruncateFree, except it only applies to actual definitions, and not
no-op truncates which may not zero the high bits.
Also, this adds a new optimization to SimplifyDemandedBits: transform
operations like x+y into (zext (add (trunc x), (trunc y))) on targets
where all the casts are no-ops. In contexts where the high part of the
add is explicitly masked off, this allows the mask operation to be
eliminated. Fix the DAGCombiner to avoid undoing these transformations
to eliminate casts on targets where the casts are no-ops.
Also, this adds a new two-address lowering heuristic. Since
two-address lowering runs before coalescing, it helps to be able to
look through copies when deciding whether commuting and/or
three-address conversion are profitable.
Also, fix a bug in LiveInterval::MergeInClobberRanges. It didn't handle
the case that a clobber range extended both before and beyond an
existing live range. In that case, multiple live ranges need to be
added. This was exposed by the new subreg coalescing code.
Remove 2008-05-06-SpillerBug.ll. It was bugpoint-reduced, and the
spiller behavior it was looking for no longer occurrs with the new
instruction selection.
llvm-svn: 68576
x * 40
=>
shlq $3, %rdi
leaq (%rdi,%rdi,4), %rax
This has the added benefit of allowing more multiply to be folded into addressing mode. e.g.
a * 24 + b
=>
leaq (%rdi,%rdi,2), %rax
leaq (%rsi,%rax,8), %rax
llvm-svn: 67917
stoppoint nodes around until Legalize; doing this
imposed an ordering on a sequence of loads that
came from different lines, interfering with scheduling.
llvm-svn: 67692
help out the register pressure reduction heuristics in the case of
nodes with multiple uses. Currently this uses very conservative
heuristics, so it doesn't have a broad impact, but in cases where it
does help it can make a big difference.
llvm-svn: 67586
a data dependency on the load node, so it really needs a
data-dependence edge to the load node, even if the load previously
existed.
And add a few comments.
llvm-svn: 67554
size by the array amount as an i32 value instead of promoting from
i32 to i64 then doing the multiply. Not doing this broke wrap-around
assumptions that the optimizers (validly) made. The ultimate real
fix for this is to introduce i64 version of alloca and remove mallocinst.
This fixes PR3829
llvm-svn: 67093
vector shuffle mask. Forced the mask to be built using i32. Note: this will
be irrelevant once vector_shuffle no longer takes a build vector for the
shuffle mask.
llvm-svn: 67076
if FPConstant is legal because if the FPConstant doesn't need to be stored
in a constant pool, the transformation is unlikely to be profitable.
llvm-svn: 66994
ptrtoint and inttoptr in X86FastISel. These casts aren't always
handled in the generic FastISel code because X86 sometimes needs
custom code to do truncation and zero-extension.
llvm-svn: 66988
by inserting explicit zero extensions where necessary. Included
is a testcase where SelectionDAG produces a virtual register
holding an i1 value which FastISel previously mistakenly assumed
to be zero-extended.
llvm-svn: 66941
1. ConstantPoolSDNode alignment field is log2 value of the alignment requirement. This is not consistent with other SDNode variants.
2. MachineConstantPool alignment field is also a log2 value.
3. However, some places are creating ConstantPoolSDNode with alignment value rather than log2 values. This creates entries with artificially large alignments, e.g. 256 for SSE vector values.
4. Constant pool entry offsets are computed when they are created. However, asm printer group them by sections. That means the offsets are no longer valid. However, asm printer uses them to determine size of padding between entries.
5. Asm printer uses expensive data structure multimap to track constant pool entries by sections.
6. Asm printer iterate over SmallPtrSet when it's emitting constant pool entries. This is non-deterministic.
Solutions:
1. ConstantPoolSDNode alignment field is changed to keep non-log2 value.
2. MachineConstantPool alignment field is also changed to keep non-log2 value.
3. Functions that create ConstantPool nodes are passing in non-log2 alignments.
4. MachineConstantPoolEntry no longer keeps an offset field. It's replaced with an alignment field. Offsets are not computed when constant pool entries are created. They are computed on the fly in asm printer and JIT.
5. Asm printer uses cheaper data structure to group constant pool entries.
6. Asm printer compute entry offsets after grouping is done.
7. Change JIT code to compute entry offsets on the fly.
llvm-svn: 66875
related transformations out of target-specific dag combine into the
ARM backend. These were added by Evan in r37685 with no testcases
and only seems to help ARM (e.g. test/CodeGen/ARM/select_xform.ll).
Add some simple X86-specific (for now) DAG combines that turn things
like cond ? 8 : 0 -> (zext(cond) << 3). This happens frequently
with the recently added cp constant select optimization, but is a
very general xform. For example, we now compile the second example
in const-select.ll to:
_test:
movsd LCPI2_0, %xmm0
ucomisd 8(%esp), %xmm0
seta %al
movzbl %al, %eax
movl 4(%esp), %ecx
movsbl (%ecx,%eax,4), %eax
ret
instead of:
_test:
movl 4(%esp), %eax
leal 4(%eax), %ecx
movsd LCPI2_0, %xmm0
ucomisd 8(%esp), %xmm0
cmovbe %eax, %ecx
movsbl (%ecx), %eax
ret
This passes multisource and dejagnu.
llvm-svn: 66779
alignment of the generated constant pool entry to the
desired alignment of a type. If we don't do this, we end up
trying to do movsd from 4-byte alignment memory. This fixes
450.soplex and 456.hmmer.
llvm-svn: 66641
Duncan Sands