This shrinks the immediate that isel table needs to emit for these
instructions. Hoping this allows me to change OPC_EmitInteger to
use a better variable length encoding for representing negative
numbers. Similar to what was done a few months ago for OPC_CheckInteger.
The alternative encoding uses less bytes for negative numbers, but
increases the number of bytes need to encode 64 which was a very
common number in the RISCV table due to SEW=64. By using Log2 this
becomes 6 and is no longer a problem.
DAGCombiner was recently taught how to combine STEP_VECTOR nodes,
meaning the step value is no longer guaranteed to be one by the time it
reaches the backend for lowering.
This patch supports such cases on RISC-V by lowering to other step
values to a multiply following the vid.v instruction. It includes a
small optimization for common cases where the multiply can be expressed
as a shift left.
Reviewed By: rogfer01
Differential Revision: https://reviews.llvm.org/D100856
When rvv vector objects existed, using sp to access the fixed stack object will pass the rvv vector objects field. So the StackOffset needs add a scalable offset of the size of rvv vector objects field
Differential Revision: https://reviews.llvm.org/D100286
Similar for or/xor with 0 in place of -1.
This is the canonical form produced by InstCombine for something like `c ? x & y : x;` Since we have to use control flow to expand select we'll usually end up with a mv in basic block. By folding this we may be able to pull the and/or/xor into the block instead and avoid a mv instruction.
The code here is based on code from ARM that uses this to create predicated instructions. I'm doing it on SELECT_CC so it happens late, but we could do it on select earlier which is what ARM does. I'm not sure if we lose any combine opportunities if we do it earlier.
I left out add and sub because this can separate sext.w from the add/sub. It also made a conditional i64 addition/subtraction on RV32 worse. I guess both of those would be fixed by doing this earlier on select.
The select-binop-identity.ll test has not been commited yet, but I made the diff show the changes to it.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D101485
This replaces D98479.
This allows type legalization to form SPLAT_VECTOR_PARTS so we don't
lose the splattedness when the scalar type is split.
I'm handling SPLAT_VECTOR_PARTS for fixed vectors separately so
we can continue using non-VL nodes for scalable vectors.
I limited to RV32+vXi64 because DAGCombiner::visitBUILD_VECTOR likes
to form SPLAT_VECTOR before seeing if it can replace the BUILD_VECTOR
with other operations. Especially interesting is a splat BUILD_VECTOR of
the extract_vector_elt which can become a splat shuffle, but won't if
we form SPLAT_VECTOR first. We either need to reorder visitBUILD_VECTOR
or add visitSPLAT_VECTOR.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D100803
This seems like a reasonable upper bound on VL. WG discussions for
the V spec would probably allow us to use 2^16 as an upper bound
on VLEN, but this is good enough for now.
This allows us to remove sext and zext if user happens to assign
the size_t result into an int and then uses it as a VL intrinsic
argument which is size_t.
Reviewed By: frasercrmck, rogfer01, arcbbb
Differential Revision: https://reviews.llvm.org/D101472
This is an complementary/alternative fix for D99068. It takes a slightly
different approach by explicitly summing up all of the required split
part type sizes and ensuring we allocate enough space for them. It also
takes the maximum alignment of each part.
Compared with D99068 there are fewer changes to the stack objects in
existing tests. However, @luismarques has shown in that patch that there
are opportunities to reduce our stack usage in the future.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D99087
This adds a special operand type that is allowed to be either
an immediate or register. By giving it a unique operand type the
machine verifier will ignore it.
This perturbs a lot of tests but mostly it is just slightly different
instruction orders. Something bad did happen to some min/max reduction
tests. We're spilling vector registers when we weren't before.
Reviewed By: khchen
Differential Revision: https://reviews.llvm.org/D101246
This modifies my previous patch to push the strided load formation
to isel. This gives us opportunity to fold the splat into a .vx
operation first. Using a scalar register and a .vx operation reduces
vector register pressure which can be important for larger LMULs.
If we can't fold the splat into a .vx operation, then it can make
sense to use a strided load to free up the vector arithmetic
ALU to do actual arithmetic rather than tying it up with vmv.v.x.
Reviewed By: khchen
Differential Revision: https://reviews.llvm.org/D101138
We have several extensions that need i32 to be Custom for
INTRINSIC_WO_CHAIN with RV64 so enable it for all RV64.
For V extension, make i32 Custom for RV64 and i64 Custom for RV32.
When the i32 or i64 is legal, the operation action doesn't matter.
LegalizeDAG checks MVT::Other rather than the real type.
This teaches DAG combine that shift amount operands for grev, gorc
shfl, unshfl only read a few bits.
This also teaches DAG combine that grevw, gorcw, shflw, unshflw,
bcompressw, bdecompressw only consume the lower 32 bits of their
inputs.
In the future we can teach SimplifyDemandedBits to also propagate
demanded bits of the output to the inputs in some cases.
Use getContainerForFixedLengthVector and getRegClassIDForVecVT to
get the register class to use when making a fixed vector type legal.
Inline it into the other two call sites.
I'm looking into using fractional lmul for fixed length vectors
and getLMULForFixedLengthVector returned an integer making it
unable to express this. I considered returning the LMUL
enum, but that seemed like it would introduce more complexity to
convert it for use.
Make it a static function RISCVISelLowering, the only place it
is used.
I think I'm going to make this return a fractional LMULs in some
cases so I'm sorting out where it should live before I start
making changes.
We can have RISCVISelDAGToDAG.cpp call the VT only version by
finding the RISCVTargetLowering object via the Subtarget.
Make the static versions just global static functions in
RISCVISelLowering that can be called by static functions in that
file.
Theses instructions are allowed to write v0 when they are masked.
We'll still never use v0 because of the earlyclobber constraint so
this doesn't really help anything. It just makes the definitions
correct.
While I was there remove an unused multiclass I noticed.
Reviewed By: HsiangKai
Differential Revision: https://reviews.llvm.org/D101118
This patch adds support for both scalable- and fixed-length vector code
lowering of the llvm.minnum and llvm.maxnum intrinsics to the equivalent
RVV instructions.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D101035
These instructions don't really exist, but we have ways we can
emulate them.
.vv will swap operands and use vmsle().vv. .vi will adjust the
immediate and use .vmsgt(u).vi when possible. For .vx we need to
use some of the multiple instruction sequences from the V extension
spec.
For unmasked vmsge(u).vx we use:
vmslt{u}.vx vd, va, x; vmnand.mm vd, vd, vd
For cases where mask and maskedoff are the same value then we have
vmsge{u}.vx v0, va, x, v0.t which is the vd==v0 case that
requires a temporary so we use:
vmslt{u}.vx vt, va, x; vmandnot.mm vd, vd, vt
For other masked cases we use this sequence:
vmslt{u}.vx vd, va, x, v0.t; vmxor.mm vd, vd, v0
We trust that register allocation will prevent vd in vmslt{u}.vx
from being v0 since v0 is still needed by the vmxor.
Differential Revision: https://reviews.llvm.org/D100925
Refactor to use new multiclass instead of individual patterns.
We already supported this due to SEW=64 on RV32, but we didn't have
test cases for all the types we supported.
Part of D100925
We don't have instructions for these, but can swap the operands
to use vmle/vmflt. This makes the IR interface more consistent and
simplifies the frontend implementation.
Part of D100925
Implementations are allowed to optimize an x0 stride to perform
less memory accesses. This is the case in SiFive cores.
No idea if this is the case in other implementations. We might
need a tuning flag for this.
Reviewed By: frasercrmck, arcbbb
Differential Revision: https://reviews.llvm.org/D100815
Rather than doing splatting each separately and doing bit manipulation
to merge them in the vector domain, copy the data to the stack
and splat it using a strided load with x0 stride. At least on
some implementations this vector load is optimized to not do
a load for each element.
This is equivalent to how we move i64 to f64 on RV32.
I've only implemented this for the intrinsic fallbacks in this
patch. I think we do similar splatting/shifting/oring in other
places. If this is approved, I'll refactor the others to share
the code.
Differential Revision: https://reviews.llvm.org/D101002
The value is always an immediate and can never be in a register.
This the kind of thing TargetConstant is for.
Saves a step GenDAGISel to convert a Constant to a TargetConstant.
This recognizes the case when Hi is (sra Lo, 31). We can use
SPLAT_VECTOR_I64 rather than splatting the high bits and
combining them in the vector register.
This previously made references to 2.3-draft which was a short
lived version number in 2017. It was replaced by date based
versions leading up to ratification.
This patch uses the latest ratified version number and just says
what the behavior is. Nothing here is in flux.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D100878
This was checked in some asserts, but not enforced by the
instruction matching.
There's still a second bug that we don't check that vt and vd
are different registers, but that will require custom checking.
Differential Revision: https://reviews.llvm.org/D100928
This patch fixes a case missed out by D100574, in which RVV scalable
stack offset computations may require three live registers in the case
where the offset's fixed component is 12 bits or larger and has a
scalable component.
Instead of adding an additional emergency spill slot, this patch further
optimizes the scalable stack offset computation sequences to reduce
register usage.
By emitting the sequence to compute the scalable component before the
fixed component, we can free up one scratch register to be reallocated
by the sequence for the fixed component. Doing this saves one register
and thus one additional emergency spill slot.
Compare:
$x5 = LUI 1
$x1 = ADDIW killed $x5, -1896
$x1 = ADD $x2, killed $x1
$x5 = PseudoReadVLENB
$x6 = ADDI $x0, 50
$x5 = MUL killed $x5, killed $x6
$x1 = ADD killed $x1, killed $x5
versus:
$x5 = PseudoReadVLENB
$x1 = ADDI $x0, 50
$x5 = MUL killed $x5, killed $x1
$x1 = LUI 1
$x1 = ADDIW killed $x1, -1896
$x1 = ADD $x2, killed $x1
$x1 = ADD killed $x1, killed $x5
Reviewed By: HsiangKai
Differential Revision: https://reviews.llvm.org/D100847
New registers FRM, FFLAGS and FCSR was defined. They represent
corresponding system registers. The new registers are necessary to
properly order floating point instructions in non-default modes.
Differential Revision: https://reviews.llvm.org/D99083
This patch adds an additional emergency spill slot to RVV code. This is
required as RVV stack offsets may require an additional register to compute.
This patch includes an optimization by @HsiangKai <kai.wang@sifive.com>
to reduce the number of registers required for the computation of stack
offsets from 3 to 2. Otherwise we'd need two additional emergency spill
slots.
Reviewed By: HsiangKai
Differential Revision: https://reviews.llvm.org/D100574
It's necessary to calculate correct instruction size because
PseudoVRELOAD and PseudoSPILL will be expanded into multiple
instructions.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D100702
As noted in the FIXME there's a sort of agreement that the any
extra bits stored will be 0.
The generated code is pretty terrible. I was really hoping we
could use a tail undisturbed trick, but tail undisturbed no
longer applies to masked destinations in the current draft
spec.
Fingers crossed that it isn't common to do this. I doubt IR
from clang or the vectorizer would ever create this kind of store.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D100618
This patch extends the lowering of RVV fixed-length vector shuffles to
avoid the default stack expansion and instead lower to vrgather
instructions.
For "permute"-style shuffles where one vector is swizzled, we can lower
to one vrgather. For shuffles involving two vector operands, we lower to
one unmasked vrgather (or splat, where appropriate) followed by a masked
vrgather which blends in the second half.
On occasion, when it's not possible to create a legal BUILD_VECTOR for
the indices, we use vrgatherei16 instructions with 16-bit index types.
For 8-bit element vectors where we may have indices over 255, we have a
fairly blunt fallback to the stack expansion to avoid custom-splitting
of the vector types.
To enable the selection of masked vrgather instructions, this patch
extends the various RISCVISD::VRGATHER nodes to take a passthru operand.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D100549
It has to save all caller-saved registers before a call in the handler.
So don't emit a call that save/restore registers.
Reviewed By: simoncook, luismarques, asb
Differential Revision: https://reviews.llvm.org/D100532
This generalizes RVInstIShift/RVInstIShiftW to take the upper
5 or 7 bits of the immediate as an input instead of only bit 30. Then
we can share them.
For RVInstIShift I left a hardcoded 0 at bit 26 where RV128 gets
a 7th bit for the shift amount.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D100424
Craig Topper