commit 5a53249d149f48b558368c5338b9921b76a12f8c upstream.
kvm_xen_schedop_poll does a kmalloc_array() when a VM polls the host
for more than one event channel potr (nr_ports > 1).
After the kmalloc_array(), the error paths need to go through the
"out" label, but the call to kvm_read_guest_virt() does not.
Fixes: 92c58965e9 ("KVM: x86/xen: Use kvm_read_guest_virt() instead of open-coding it badly")
Reviewed-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Manuel Andreas <manuel.andreas@tum.de>
[Adjusted commit message. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 3ee59c38ae7369ad1f7b846e05633ccf0d159fab)
commit 2d7521aa26ec2dc8b877bb2d1f2611a2df49a3cf upstream.
On 11 Oct 2022, it was reported that the crc32 verification
of the u-boot environment failed only on big-endian systems
for the u-boot-env nvmem layout driver with the following error.
Invalid calculated CRC32: 0x88cd6f09 (expected: 0x096fcd88)
This problem has been present since the driver was introduced,
and before it was made into a layout driver.
The suggested fix at the time was to use further endianness
conversion macros in order to have both the stored and calculated
crc32 values to compare always represented in the system's endianness.
This was not accepted due to sparse warnings
and some disagreement on how to handle the situation.
Later on in a newer revision of the patch, it was proposed to use
cpu_to_le32() for both values to compare instead of le32_to_cpu()
and store the values as __le32 type to remove compilation errors.
The necessity of this is based on the assumption that the use of crc32()
requires endianness conversion because the algorithm uses little-endian,
however, this does not prove to be the case and the issue is unrelated.
Upon inspecting the current kernel code,
there already is an existing use of le32_to_cpu() in this driver,
which suggests there already is special handling for big-endian systems,
however, it is big-endian systems that have the problem.
This, being the only functional difference between architectures
in the driver combined with the fact that the suggested fix
was to use the exact same endianness conversion for the values
brings up the possibility that it was not necessary to begin with,
as the same endianness conversion for two values expected to be the same
is expected to be equivalent to no conversion at all.
After inspecting the u-boot environment of devices of both endianness
and trying to remove the existing endianness conversion,
the problem is resolved in an equivalent way as the other suggested fixes.
Ultimately, it seems that u-boot is agnostic to endianness
at least for the purpose of environment variables.
In other words, u-boot reads and writes the stored crc32 value
with the same endianness that the crc32 value is calculated with
in whichever endianness a certain architecture runs on.
Therefore, the u-boot-env driver does not need to convert endianness.
Remove the usage of endianness macros in the u-boot-env driver,
and change the type of local variables to maintain the same return type.
If there is a special situation in the case of endianness,
it would be a corner case and should be handled by a unique "compatible".
Even though it is not necessary to use endianness conversion macros here,
it may be useful to use them in the future for consistent error printing.
Fixes: d5542923f2 ("nvmem: add driver handling U-Boot environment variables")
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://lore.kernel.org/all/20221011024928.1807-1-musashino.open@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: "Michael C. Pratt" <mcpratt@pm.me>
Signed-off-by: Srinivas Kandagatla <srini@kernel.org>
Link: https://lore.kernel.org/r/20250716144210.4804-1-srini@kernel.org
[ applied changes to drivers/nvmem/u-boot-env.c before code was moved to
drivers/nvmem/layouts/u-boot-env.c ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 48e8791843206baf76827df1b6ee3cb88a2a17d8)
commit e66b0a8f04 upstream.
Using of_property_read_bool() for non-boolean properties is deprecated
and results in a warning during runtime since commit c141ecc3ce ("of:
Warn when of_property_read_bool() is used on non-boolean properties").
Fixes: b6ef830c60 ("i2c: omap: Add support for setting mux")
Cc: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Link: https://lore.kernel.org/r/20250415075230.16235-1-johan+linaro@kernel.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 35542cbe66c67c65dff866a4a68083a533730726)
This reverts commit e7d193073a223663612301c659e53795b991ca89 which is
commit 6a2d30d3c5 upstream.
The dummy_st_ops/dummy_sleepable_reject_null test requires commit 980ca8ceea
("bpf: check bpf_dummy_struct_ops program params for test runs"), which in turn
depends on "Support PTR_MAYBE_NULL for struct_ops arguments" series (see link
below), neither are backported to stable 6.6.
Link: https://lore.kernel.org/all/20240209023750.1153905-1-thinker.li@gmail.com/
Signed-off-by: Shung-Hsi Yu <shung-hsi.yu@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 056b65a02edc6321503fb47f191432df8a6fc80c)
commit dc78f7e59169d3f0e6c3c95d23dc8e55e95741e2 upstream.
On an imx8mm platform with an external clock provider, when running the
receiver (arecord) and triggering an xrun with xrun_injection, we see a
channel swap/offset. This happens sometimes when running only the
receiver, but occurs reliably if a transmitter (aplay) is also
concurrently running.
It seems that the SAI loses track of frame sync during the trigger stop
-> trigger start cycle that occurs during an xrun. Doing just a FIFO
reset in this case does not suffice, and only a software reset seems to
get it back on track.
This looks like the same h/w bug that is already handled for the
producer case, so we now do the reset unconditionally on config disable.
Signed-off-by: Arun Raghavan <arun@asymptotic.io>
Reported-by: Pieterjan Camerlynck <p.camerlynck@televic.com>
Fixes: 3e3f8bd569 ("ASoC: fsl_sai: fix no frame clk in master mode")
Cc: stable@vger.kernel.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://patch.msgid.link/20250626130858.163825-1-arun@arunraghavan.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit b9e50a5169b086dd5915ae117c8a53cd75403574)
commit b3cbdcc191 upstream.
Odroid-C1 uses a Monolithic Power Systems MP2161 controlled via PWM for
the VDDEE voltage supply of the Meson8b SoC. Commit 6b9352f3f8 ("pwm:
meson: modify and simplify calculation in meson_pwm_get_state") results
in my Odroid-C1 crashing with memory corruption in many different places
(seemingly at random). It turns out that this is due to a currently not
supported corner case.
The VDDEE regulator can generate between 860mV (duty cycle of ~91%) and
1140mV (duty cycle of 0%). We consider it to be enabled by the bootloader
(which is why it has the regulator-boot-on flag in .dts) as well as
being always-on (which is why it has the regulator-always-on flag in
.dts) because the VDDEE voltage is generally required for the Meson8b
SoC to work. The public S805 datasheet [0] states on page 17 (where "A5"
refers to the Cortex-A5 CPU cores):
[...] So if EE domains is shut off, A5 memory is also shut off. That
does not matter. Before EE power domain is shut off, A5 should be shut
off at first.
It turns out that at least some bootloader versions are keeping the PWM
output disabled. This is not a problem due to the specific design of the
regulator: when the PWM output is disabled the output pin is pulled LOW,
effectively achieving a 0% duty cycle (which in return means that VDDEE
voltage is at 1140mV).
The problem comes when the pwm-regulator driver tries to initialize the
PWM output. To do so it reads the current state from the hardware, which
is:
period: 3666ns
duty cycle: 3333ns (= ~91%)
enabled: false
Then those values are translated using the continuous voltage range to
860mV.
Later, when the regulator is being enabled (either by the regulator core
due to the always-on flag or first consumer - in this case the lima
driver for the Mali-450 GPU) the pwm-regulator driver tries to keep the
voltage (at 860mV) and just enable the PWM output. This is when things
start to go wrong as the typical voltage used for VDDEE is 1100mV.
Commit 6b9352f3f8 ("pwm: meson: modify and simplify calculation in
meson_pwm_get_state") triggers above condition as before that change
period and duty cycle were both at 0. Since the change to the pwm-meson
driver is considered correct the solution is to be found in the
pwm-regulator driver. Update the duty cycle during driver probe if the
regulator is flagged as boot-on so that a call to pwm_regulator_enable()
(by the regulator core during initialization of a regulator flagged with
boot-on) without any preceding call to pwm_regulator_set_voltage() does
not change the output voltage.
[0] https://dn.odroid.com/S805/Datasheet/S805_Datasheet%20V0.8%2020150126.pdf
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://msgid.link/r/20240113224628.377993-4-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 8f2852c1d7aab936a60a4c9257dcf7ab9ad46336)
commit 6a7d11efd6 upstream.
If a PWM output is disabled then it's voltage has to be calculated
based on a zero duty cycle (for normal polarity) or duty cycle being
equal to the PWM period (for inverted polarity). Add support for this
to pwm_regulator_get_voltage().
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://msgid.link/r/20240113224628.377993-3-martin.blumenstingl@googlemail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit cad3ec23e398542c28283bcf3708dc4b71c2eb75)
commit b6ef830c60 upstream.
Some SoCs require muxes in the routing for SDA and SCL lines.
Therefore, add support for setting the mux by reading the mux-states
property from the dt-node.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Link: https://lore.kernel.org/r/20250318103622.29979-3-j-choudhary@ti.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Stable-dep-of: a9503a2ecd95 ("i2c: omap: Handle omap_i2c_init() errors in omap_i2c_probe()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit caa86f8b6c30b109a6511322aa9680afe13d3397)
commit ef8abc0ba49ce717e6bc4124e88e59982671f3b5 upstream.
Leaving the USB BCR asserted prevents the associated GDSC to turn on. This
blocks any subsequent attempts of probing the device, e.g. after a probe
deferral, with the following showing in the log:
[ 1.332226] usb30_prim_gdsc status stuck at 'off'
Leave the BCR deasserted when exiting the driver to avoid this issue.
Cc: stable <stable@kernel.org>
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20250709132900.3408752-1-krishna.kurapati@oss.qualcomm.com
[ adapted to individual clock management instead of bulk clock operations ]
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 6cfbff5f8dc9982aaa253dbb515c5834d008c103)
commit 2521106fc732b0b75fd3555c689b1ed1d29d273c upstream.
Hub driver warm-resets ports in SS.Inactive or Compliance mode to
recover a possible connected device. The port reset code correctly
detects if a connection is lost during reset, but hub driver
port_event() fails to take this into account in some cases.
port_event() ends up using stale values and assumes there is a
connected device, and will try all means to recover it, including
power-cycling the port.
Details:
This case was triggered when xHC host was suspended with DbC (Debug
Capability) enabled and connected. DbC turns one xHC port into a simple
usb debug device, allowing debugging a system with an A-to-A USB debug
cable.
xhci DbC code disables DbC when xHC is system suspended to D3, and
enables it back during resume.
We essentially end up with two hosts connected to each other during
suspend, and, for a short while during resume, until DbC is enabled back.
The suspended xHC host notices some activity on the roothub port, but
can't train the link due to being suspended, so xHC hardware sets a CAS
(Cold Attach Status) flag for this port to inform xhci host driver that
the port needs to be warm reset once xHC resumes.
CAS is xHCI specific, and not part of USB specification, so xhci driver
tells usb core that the port has a connection and link is in compliance
mode. Recovery from complinace mode is similar to CAS recovery.
xhci CAS driver support that fakes a compliance mode connection was added
in commit 8bea2bd37d ("usb: Add support for root hub port status CAS")
Once xHCI resumes and DbC is enabled back, all activity on the xHC
roothub host side port disappears. The hub driver will anyway think
port has a connection and link is in compliance mode, and hub driver
will try to recover it.
The port power-cycle during recovery seems to cause issues to the active
DbC connection.
Fix this by clearing connect_change flag if hub_port_reset() returns
-ENOTCONN, thus avoiding the whole unnecessary port recovery and
initialization attempt.
Cc: stable@vger.kernel.org
Fixes: 8bea2bd37d ("usb: Add support for root hub port status CAS")
Tested-by: Łukasz Bartosik <ukaszb@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20250623133947.3144608-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 824fa25c85e869018502e8d5450d2eef1c0ff3af)
commit 9bd9c8026341f75f25c53104eb7e656e357ca1a2 upstream.
Delayed work that prevents USB3 hubs from runtime-suspending too early
needed to be flushed in hub_quiesce() to resolve issues detected on
QC SC8280XP CRD board during suspend resume testing.
This flushing did however trigger new issues on Raspberry Pi 3B+, which
doesn't have USB3 ports, and doesn't queue any post resume delayed work.
The flushed 'hub->init_work' item is used for several purposes, and
is originally initialized with a 'NULL' work function. The work function
is also changed on the fly, which may contribute to the issue.
Solve this by creating a dedicated delayed work item for post resume work,
and flush that delayed work in hub_quiesce()
Cc: stable <stable@kernel.org>
Fixes: a49e1e2e785f ("usb: hub: Fix flushing and scheduling of delayed work that tunes runtime pm")
Reported-by: Mark Brown <broonie@kernel.org>
Closes: https://lore.kernel.org/linux-usb/aF5rNp1l0LWITnEB@finisterre.sirena.org.uk
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> # SC8280XP CRD
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20250627164348.3982628-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 668c7b47a5eec8b3beb5b97d0a3a33699d6e1d1e)
commit a49e1e2e785fb3621f2d748581881b23a364998a upstream.
Delayed work to prevent USB3 hubs from runtime-suspending immediately
after resume was added in commit 8f5b7e2bec1c ("usb: hub: fix detection
of high tier USB3 devices behind suspended hubs").
This delayed work needs be flushed if system suspends, or hub needs to
be quiesced for other reasons right after resume. Not flushing it
triggered issues on QC SC8280XP CRD board during suspend/resume testing.
Fix it by flushing the delayed resume work in hub_quiesce()
The delayed work item that allow hub runtime suspend is also scheduled
just before calling autopm get. Alan pointed out there is a small risk
that work is run before autopm get, which would call autopm put before
get, and mess up the runtime pm usage order.
Swap the order of work sheduling and calling autopm get to solve this.
Cc: stable <stable@kernel.org>
Fixes: 8f5b7e2bec1c ("usb: hub: fix detection of high tier USB3 devices behind suspended hubs")
Reported-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Closes: https://lore.kernel.org/linux-usb/acaaa928-832c-48ca-b0ea-d202d5cd3d6c@oss.qualcomm.com
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Closes: https://lore.kernel.org/linux-usb/c73fbead-66d7-497a-8fa1-75ea4761090a@rowland.harvard.edu
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250626130102.3639861-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 71f5c98d2931eea3f1b4d6c4771215b8448f5d2b)
commit 8f5b7e2bec1c36578fdaa74a6951833541103e27 upstream.
USB3 devices connected behind several external suspended hubs may not
be detected when plugged in due to aggressive hub runtime pm suspend.
The hub driver immediately runtime-suspends hubs if there are no
active children or port activity.
There is a delay between the wake signal causing hub resume, and driver
visible port activity on the hub downstream facing ports.
Most of the LFPS handshake, resume signaling and link training done
on the downstream ports is not visible to the hub driver until completed,
when device then will appear fully enabled and running on the port.
This delay between wake signal and detectable port change is even more
significant with chained suspended hubs where the wake signal will
propagate upstream first. Suspended hubs will only start resuming
downstream ports after upstream facing port resumes.
The hub driver may resume a USB3 hub, read status of all ports, not
yet see any activity, and runtime suspend back the hub before any
port activity is visible.
This exact case was seen when conncting USB3 devices to a suspended
Thunderbolt dock.
USB3 specification defines a 100ms tU3WakeupRetryDelay, indicating
USB3 devices expect to be resumed within 100ms after signaling wake.
if not then device will resend the wake signal.
Give the USB3 hubs twice this time (200ms) to detect any port
changes after resume, before allowing hub to runtime suspend again.
Cc: stable <stable@kernel.org>
Fixes: 2839f5bcfc ("USB: Turn on auto-suspend for USB 3.0 hubs.")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20250611112441.2267883-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 15fea75a788681dd36a869dd90ff4f0461ea0714)
commit a75ad2fc76a2ab70817c7eed3163b66ea84ca6ac upstream.
We have a number of hwcaps for various SME subfeatures enumerated via
ID_AA64SMFR0_EL1. Currently we advertise these without cross checking
against the main SME feature, advertised in ID_AA64PFR1_EL1.SME which
means that if the two are out of sync userspace can see a confusing
situation where SME subfeatures are advertised without the base SME
hwcap. This can be readily triggered by using the arm64.nosme override
which only masks out ID_AA64PFR1_EL1.SME, and there have also been
reports of VMMs which do the same thing.
Fix this as we did previously for SVE in 064737920b ("arm64: Filter
out SVE hwcaps when FEAT_SVE isn't implemented") by filtering out the
SME subfeature hwcaps when FEAT_SME is not present.
Fixes: 5e64b862c4 ("arm64/sme: Basic enumeration support")
Reported-by: Yury Khrustalev <yury.khrustalev@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250620-arm64-sme-filter-hwcaps-v1-1-02b9d3c2d8ef@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit d5024dc5e6446fc01f28d5d7cdf8d84677ef87c0)
commit c28f922c9dcee0e4876a2c095939d77fe7e15116 upstream.
What we want is to verify there is that clone won't expose something
hidden by a mount we wouldn't be able to undo. "Wouldn't be able to undo"
may be a result of MNT_LOCKED on a child, but it may also come from
lacking admin rights in the userns of the namespace mount belongs to.
clone_private_mnt() checks the former, but not the latter.
There's a number of rather confusing CAP_SYS_ADMIN checks in various
userns during the mount, especially with the new mount API; they serve
different purposes and in case of clone_private_mnt() they usually,
but not always end up covering the missing check mentioned above.
Reviewed-by: Christian Brauner <brauner@kernel.org>
Reported-by: "Orlando, Noah" <Noah.Orlando@deshaw.com>
Fixes: 427215d85e ("ovl: prevent private clone if bind mount is not allowed")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ merge conflict resolution: clone_private_mount() was reworked in
db04662e2f ("fs: allow detached mounts in clone_private_mount()").
Tweak the relevant ns_capable check so that it works on older kernels ]
Signed-off-by: Noah Orlando <Noah.Orlando@deshaw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit dc6a664089f10eab0fb36b6e4f705022210191d2)
commit dfd2ee086a upstream.
Both addrconf_verify_work() and addrconf_dad_work() acquire rtnl,
there is no point trying to have one thread per cpu.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20240201173031.3654257-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Brett A C Sheffield <bacs@librecast.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4cb17b11c8af2fa9de840ffe7fc0bb712f894242)
commit 36569780b0d64de283f9d6c2195fd1a43e221ee8 upstream.
The commit e6fe3f422b ("sched: Make multiple runqueue task counters
32-bit") changed nr_uninterruptible to an unsigned int. But the
nr_uninterruptible values for each of the CPU runqueues can grow to
large numbers, sometimes exceeding INT_MAX. This is valid, if, over
time, a large number of tasks are migrated off of one CPU after going
into an uninterruptible state. Only the sum of all nr_interruptible
values across all CPUs yields the correct result, as explained in a
comment in kernel/sched/loadavg.c.
Change the type of nr_uninterruptible back to unsigned long to prevent
overflows, and thus the miscalculation of load average.
Fixes: e6fe3f422b ("sched: Make multiple runqueue task counters 32-bit")
Signed-off-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20250709173328.606794-1-aruna.ramakrishna@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 496efa228f0dd58980d301e379e5561a9b612eaa)
[ Upstream commit 14a67b42cb6f3ab66f41603c062c5056d32ea7dd ]
This reverts commit cff5f49d43.
Commit cff5f49d43 ("cgroup_freezer: cgroup_freezing: Check if not
frozen") modified the cgroup_freezing() logic to verify that the FROZEN
flag is not set, affecting the return value of the freezing() function,
in order to address a warning in __thaw_task.
A race condition exists that may allow tasks to escape being frozen. The
following scenario demonstrates this issue:
CPU 0 (get_signal path) CPU 1 (freezer.state reader)
try_to_freeze read freezer.state
__refrigerator freezer_read
update_if_frozen
WRITE_ONCE(current->__state, TASK_FROZEN);
...
/* Task is now marked frozen */
/* frozen(task) == true */
/* Assuming other tasks are frozen */
freezer->state |= CGROUP_FROZEN;
/* freezing(current) returns false */
/* because cgroup is frozen (not freezing) */
break out
__set_current_state(TASK_RUNNING);
/* Bug: Task resumes running when it should remain frozen */
The existing !frozen(p) check in __thaw_task makes the
WARN_ON_ONCE(freezing(p)) warning redundant. Removing this warning enables
reverting the commit cff5f49d43 ("cgroup_freezer: cgroup_freezing: Check
if not frozen") to resolve the issue.
The warning has been removed in the previous patch. This patch revert the
commit cff5f49d43 ("cgroup_freezer: cgroup_freezing: Check if not
frozen") to complete the fix.
Fixes: cff5f49d43 ("cgroup_freezer: cgroup_freezing: Check if not frozen")
Reported-by: Zhong Jiawei<zhongjiawei1@huawei.com>
Signed-off-by: Chen Ridong <chenridong@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit f371ad6471ee1036b90eef1cab764cdff029c37e)
[ Upstream commit e9c0b96ec0a34fcacdf9365713578d83cecac34c ]
Under some circumstances, such as when a server socket is closing, ABORT
packets will be generated in response to incoming packets. Unfortunately,
this also may include generating aborts in response to incoming aborts -
which may cause a cycle. It appears this may be made possible by giving
the client a multicast address.
Fix this such that rxrpc_reject_packet() will refuse to generate aborts in
response to aborts.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Linus Torvalds <torvalds@linux-foundation.org>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-5-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 74bb4de32d92e9eda56680bc720edc662d416269)
[ Upstream commit 962fb1f651c2cf2083e0c3ef53ba69e3b96d3fbc ]
If a call receives an event (such as incoming data), the call gets placed
on the socket's queue and a thread in recvmsg can be awakened to go and
process it. Once the thread has picked up the call off of the queue,
further events will cause it to be requeued, and once the socket lock is
dropped (recvmsg uses call->user_mutex to allow the socket to be used in
parallel), a second thread can come in and its recvmsg can pop the call off
the socket queue again.
In such a case, the first thread will be receiving stuff from the call and
the second thread will be blocked on call->user_mutex. The first thread
can, at this point, process both the event that it picked call for and the
event that the second thread picked the call for and may see the call
terminate - in which case the call will be "released", decoupling the call
from the user call ID assigned to it (RXRPC_USER_CALL_ID in the control
message).
The first thread will return okay, but then the second thread will wake up
holding the user_mutex and, if it sees that the call has been released by
the first thread, it will BUG thusly:
kernel BUG at net/rxrpc/recvmsg.c:474!
Fix this by just dequeuing the call and ignoring it if it is seen to be
already released. We can't tell userspace about it anyway as the user call
ID has become stale.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Reported-by: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250717074350.3767366-3-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 7692bde890061797f3dece0148d7859e85c55778)
[ Upstream commit 0e1d5d9b5c5966e2e42e298670808590db5ed628 ]
htb_lookup_leaf has a BUG_ON that can trigger with the following:
tc qdisc del dev lo root
tc qdisc add dev lo root handle 1: htb default 1
tc class add dev lo parent 1: classid 1:1 htb rate 64bit
tc qdisc add dev lo parent 1:1 handle 2: netem
tc qdisc add dev lo parent 2:1 handle 3: blackhole
ping -I lo -c1 -W0.001 127.0.0.1
The root cause is the following:
1. htb_dequeue calls htb_dequeue_tree which calls the dequeue handler on
the selected leaf qdisc
2. netem_dequeue calls enqueue on the child qdisc
3. blackhole_enqueue drops the packet and returns a value that is not
just NET_XMIT_SUCCESS
4. Because of this, netem_dequeue calls qdisc_tree_reduce_backlog, and
since qlen is now 0, it calls htb_qlen_notify -> htb_deactivate ->
htb_deactiviate_prios -> htb_remove_class_from_row -> htb_safe_rb_erase
5. As this is the only class in the selected hprio rbtree,
__rb_change_child in __rb_erase_augmented sets the rb_root pointer to
NULL
6. Because blackhole_dequeue returns NULL, netem_dequeue returns NULL,
which causes htb_dequeue_tree to call htb_lookup_leaf with the same
hprio rbtree, and fail the BUG_ON
The function graph for this scenario is shown here:
0) | htb_enqueue() {
0) + 13.635 us | netem_enqueue();
0) 4.719 us | htb_activate_prios();
0) # 2249.199 us | }
0) | htb_dequeue() {
0) 2.355 us | htb_lookup_leaf();
0) | netem_dequeue() {
0) + 11.061 us | blackhole_enqueue();
0) | qdisc_tree_reduce_backlog() {
0) | qdisc_lookup_rcu() {
0) 1.873 us | qdisc_match_from_root();
0) 6.292 us | }
0) 1.894 us | htb_search();
0) | htb_qlen_notify() {
0) 2.655 us | htb_deactivate_prios();
0) 6.933 us | }
0) + 25.227 us | }
0) 1.983 us | blackhole_dequeue();
0) + 86.553 us | }
0) # 2932.761 us | qdisc_warn_nonwc();
0) | htb_lookup_leaf() {
0) | BUG_ON();
------------------------------------------
The full original bug report can be seen here [1].
We can fix this just by returning NULL instead of the BUG_ON,
as htb_dequeue_tree returns NULL when htb_lookup_leaf returns
NULL.
[1] https://lore.kernel.org/netdev/pF5XOOIim0IuEfhI-SOxTgRvNoDwuux7UHKnE_Y5-zVd4wmGvNk2ceHjKb8ORnzw0cGwfmVu42g9dL7XyJLf1NEzaztboTWcm0Ogxuojoeo=@willsroot.io/
Fixes: 512bb43eb5 ("pkt_sched: sch_htb: Optimize WARN_ONs in htb_dequeue_tree() etc.")
Signed-off-by: William Liu <will@willsroot.io>
Signed-off-by: Savino Dicanosa <savy@syst3mfailure.io>
Link: https://patch.msgid.link/20250717022816.221364-1-will@willsroot.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 7ff2d83ecf2619060f30ecf9fad4f2a700fca344)
[ Upstream commit 683dc24da8bf199bb7446e445ad7f801c79a550e ]
Do not offload IGMP/MLD messages as it could lead to IGMP/MLD Reports
being unintentionally flooded to Hosts. Instead, let the bridge decide
where to send these IGMP/MLD messages.
Consider the case where the local host is sending out reports in response
to a remote querier like the following:
mcast-listener-process (IP_ADD_MEMBERSHIP)
\
br0
/ \
swp1 swp2
| |
QUERIER SOME-OTHER-HOST
In the above setup, br0 will want to br_forward() reports for
mcast-listener-process's group(s) via swp1 to QUERIER; but since the
source hwdom is 0, the report is eligible for tx offloading, and is
flooded by hardware to both swp1 and swp2, reaching SOME-OTHER-HOST as
well. (Example and illustration provided by Tobias.)
Fixes: 472111920f ("net: bridge: switchdev: allow the TX data plane forwarding to be offloaded")
Signed-off-by: Joseph Huang <Joseph.Huang@garmin.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250716153551.1830255-1-Joseph.Huang@garmin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 7b0d42318393186f218b8a617ff3d0a01693274c)
[ Upstream commit 579d4f9ca9a9a605184a9b162355f6ba131f678d ]
Assuming the "rx-vlan-filter" feature is enabled on a net device, the
8021q module will automatically add or remove VLAN 0 when the net device
is put administratively up or down, respectively. There are a couple of
problems with the above scheme.
The first problem is a memory leak that can happen if the "rx-vlan-filter"
feature is disabled while the device is running:
# ip link add bond1 up type bond mode 0
# ethtool -K bond1 rx-vlan-filter off
# ip link del dev bond1
When the device is put administratively down the "rx-vlan-filter"
feature is disabled, so the 8021q module will not remove VLAN 0 and the
memory will be leaked [1].
Another problem that can happen is that the kernel can automatically
delete VLAN 0 when the device is put administratively down despite not
adding it when the device was put administratively up since during that
time the "rx-vlan-filter" feature was disabled. null-ptr-unref or
bug_on[2] will be triggered by unregister_vlan_dev() for refcount
imbalance if toggling filtering during runtime:
$ ip link add bond0 type bond mode 0
$ ip link add link bond0 name vlan0 type vlan id 0 protocol 802.1q
$ ethtool -K bond0 rx-vlan-filter off
$ ifconfig bond0 up
$ ethtool -K bond0 rx-vlan-filter on
$ ifconfig bond0 down
$ ip link del vlan0
Root cause is as below:
step1: add vlan0 for real_dev, such as bond, team.
register_vlan_dev
vlan_vid_add(real_dev,htons(ETH_P_8021Q),0) //refcnt=1
step2: disable vlan filter feature and enable real_dev
step3: change filter from 0 to 1
vlan_device_event
vlan_filter_push_vids
ndo_vlan_rx_add_vid //No refcnt added to real_dev vlan0
step4: real_dev down
vlan_device_event
vlan_vid_del(dev, htons(ETH_P_8021Q), 0); //refcnt=0
vlan_info_rcu_free //free vlan0
step5: delete vlan0
unregister_vlan_dev
BUG_ON(!vlan_info); //vlan_info is null
Fix both problems by noting in the VLAN info whether VLAN 0 was
automatically added upon NETDEV_UP and based on that decide whether it
should be deleted upon NETDEV_DOWN, regardless of the state of the
"rx-vlan-filter" feature.
[1]
unreferenced object 0xffff8880068e3100 (size 256):
comm "ip", pid 384, jiffies 4296130254
hex dump (first 32 bytes):
00 20 30 0d 80 88 ff ff 00 00 00 00 00 00 00 00 . 0.............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 81ce31fa):
__kmalloc_cache_noprof+0x2b5/0x340
vlan_vid_add+0x434/0x940
vlan_device_event.cold+0x75/0xa8
notifier_call_chain+0xca/0x150
__dev_notify_flags+0xe3/0x250
rtnl_configure_link+0x193/0x260
rtnl_newlink_create+0x383/0x8e0
__rtnl_newlink+0x22c/0xa40
rtnl_newlink+0x627/0xb00
rtnetlink_rcv_msg+0x6fb/0xb70
netlink_rcv_skb+0x11f/0x350
netlink_unicast+0x426/0x710
netlink_sendmsg+0x75a/0xc20
__sock_sendmsg+0xc1/0x150
____sys_sendmsg+0x5aa/0x7b0
___sys_sendmsg+0xfc/0x180
[2]
kernel BUG at net/8021q/vlan.c:99!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 382 Comm: ip Not tainted 6.16.0-rc3 #61 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:unregister_vlan_dev (net/8021q/vlan.c:99 (discriminator 1))
RSP: 0018:ffff88810badf310 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88810da84000 RCX: ffffffffb47ceb9a
RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff88810e8b43c8
RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff6cefe80
R10: ffffffffb677f407 R11: ffff88810badf3c0 R12: ffff88810e8b4000
R13: 0000000000000000 R14: ffff88810642a5c0 R15: 000000000000017e
FS: 00007f1ff68c20c0(0000) GS:ffff888163a24000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1ff5dad240 CR3: 0000000107e56000 CR4: 00000000000006f0
Call Trace:
<TASK>
rtnl_dellink (net/core/rtnetlink.c:3511 net/core/rtnetlink.c:3553)
rtnetlink_rcv_msg (net/core/rtnetlink.c:6945)
netlink_rcv_skb (net/netlink/af_netlink.c:2535)
netlink_unicast (net/netlink/af_netlink.c:1314 net/netlink/af_netlink.c:1339)
netlink_sendmsg (net/netlink/af_netlink.c:1883)
____sys_sendmsg (net/socket.c:712 net/socket.c:727 net/socket.c:2566)
___sys_sendmsg (net/socket.c:2622)
__sys_sendmsg (net/socket.c:2652)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
Fixes: ad1afb0039 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)")
Reported-by: syzbot+a8b046e462915c65b10b@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=a8b046e462915c65b10b
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Dong Chenchen <dongchenchen2@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250716034504.2285203-2-dongchenchen2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit bb515c41306454937464da055609b5fb0a27821b)
[ Upstream commit 4ab26bce3969f8fd925fe6f6f551e4d1a508c68b ]
After recent changes in net-next TCP compacts skbs much more
aggressively. This unearthed a bug in TLS where we may try
to operate on an old skb when checking if all skbs in the
queue have matching decrypt state and geometry.
BUG: KASAN: slab-use-after-free in tls_strp_check_rcv+0x898/0x9a0 [tls]
(net/tls/tls_strp.c:436 net/tls/tls_strp.c:530 net/tls/tls_strp.c:544)
Read of size 4 at addr ffff888013085750 by task tls/13529
CPU: 2 UID: 0 PID: 13529 Comm: tls Not tainted 6.16.0-rc5-virtme
Call Trace:
kasan_report+0xca/0x100
tls_strp_check_rcv+0x898/0x9a0 [tls]
tls_rx_rec_wait+0x2c9/0x8d0 [tls]
tls_sw_recvmsg+0x40f/0x1aa0 [tls]
inet_recvmsg+0x1c3/0x1f0
Always reload the queue, fast path is to have the record in the queue
when we wake, anyway (IOW the path going down "if !strp->stm.full_len").
Fixes: 0d87bbd39d ("tls: strp: make sure the TCP skbs do not have overlapping data")
Link: https://patch.msgid.link/20250716143850.1520292-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 1f3a429c21e0e43e8b8c55d30701e91411a4df02)
[ Upstream commit d7501e076d859d2f381d57bd984ff6db13172727 ]
Set an additional flag IFF_NO_ADDRCONF to prevent ipv6 addrconf.
Commit under Fixes added a new flag change that was not made
to hv_netvsc resulting in the VF being assinged an IPv6.
Fixes: 8a321cf7be ("net: add IFF_NO_ADDRCONF and use it in bonding to prevent ipv6 addrconf")
Suggested-by: Cathy Avery <cavery@redhat.com>
Signed-off-by: Li Tian <litian@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20250716002607.4927-1-litian@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 007142a263db3d97054efccd14cfd8d64c051feb)
[ Upstream commit d24e4a7fedae121d33fb32ad785b87046527eedb ]
Configuration request only configure the incoming direction of the peer
initiating the request, so using the MTU is the other direction shall
not be used, that said the spec allows the peer responding to adjust:
Bluetooth Core 6.1, Vol 3, Part A, Section 4.5
'Each configuration parameter value (if any is present) in an
L2CAP_CONFIGURATION_RSP packet reflects an ‘adjustment’ to a
configuration parameter value that has been sent (or, in case of
default values, implied) in the corresponding
L2CAP_CONFIGURATION_REQ packet.'
That said adjusting the MTU in the response shall be limited to ERTM
channels only as for older modes the remote stack may not be able to
detect the adjustment causing it to silently drop packets.
Link: https://github.com/bluez/bluez/issues/1422
Link: https://gitlab.archlinux.org/archlinux/packaging/packages/linux/-/issues/149
Link: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/4793
Fixes: 042bb9603c44 ("Bluetooth: L2CAP: Fix L2CAP MTU negotiation")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit bd3051a816211fb3e721fe88169a7ce0d7e11c14)
[ Upstream commit 2d72afb340657f03f7261e9243b44457a9228ac7 ]
A crash in conntrack was reported while trying to unlink the conntrack
entry from the hash bucket list:
[exception RIP: __nf_ct_delete_from_lists+172]
[..]
#7 [ff539b5a2b043aa0] nf_ct_delete at ffffffffc124d421 [nf_conntrack]
#8 [ff539b5a2b043ad0] nf_ct_gc_expired at ffffffffc124d999 [nf_conntrack]
#9 [ff539b5a2b043ae0] __nf_conntrack_find_get at ffffffffc124efbc [nf_conntrack]
[..]
The nf_conn struct is marked as allocated from slab but appears to be in
a partially initialised state:
ct hlist pointer is garbage; looks like the ct hash value
(hence crash).
ct->status is equal to IPS_CONFIRMED|IPS_DYING, which is expected
ct->timeout is 30000 (=30s), which is unexpected.
Everything else looks like normal udp conntrack entry. If we ignore
ct->status and pretend its 0, the entry matches those that are newly
allocated but not yet inserted into the hash:
- ct hlist pointers are overloaded and store/cache the raw tuple hash
- ct->timeout matches the relative time expected for a new udp flow
rather than the absolute 'jiffies' value.
If it were not for the presence of IPS_CONFIRMED,
__nf_conntrack_find_get() would have skipped the entry.
Theory is that we did hit following race:
cpu x cpu y cpu z
found entry E found entry E
E is expired <preemption>
nf_ct_delete()
return E to rcu slab
init_conntrack
E is re-inited,
ct->status set to 0
reply tuplehash hnnode.pprev
stores hash value.
cpu y found E right before it was deleted on cpu x.
E is now re-inited on cpu z. cpu y was preempted before
checking for expiry and/or confirm bit.
->refcnt set to 1
E now owned by skb
->timeout set to 30000
If cpu y were to resume now, it would observe E as
expired but would skip E due to missing CONFIRMED bit.
nf_conntrack_confirm gets called
sets: ct->status |= CONFIRMED
This is wrong: E is not yet added
to hashtable.
cpu y resumes, it observes E as expired but CONFIRMED:
<resumes>
nf_ct_expired()
-> yes (ct->timeout is 30s)
confirmed bit set.
cpu y will try to delete E from the hashtable:
nf_ct_delete() -> set DYING bit
__nf_ct_delete_from_lists
Even this scenario doesn't guarantee a crash:
cpu z still holds the table bucket lock(s) so y blocks:
wait for spinlock held by z
CONFIRMED is set but there is no
guarantee ct will be added to hash:
"chaintoolong" or "clash resolution"
logic both skip the insert step.
reply hnnode.pprev still stores the
hash value.
unlocks spinlock
return NF_DROP
<unblocks, then
crashes on hlist_nulls_del_rcu pprev>
In case CPU z does insert the entry into the hashtable, cpu y will unlink
E again right away but no crash occurs.
Without 'cpu y' race, 'garbage' hlist is of no consequence:
ct refcnt remains at 1, eventually skb will be free'd and E gets
destroyed via: nf_conntrack_put -> nf_conntrack_destroy -> nf_ct_destroy.
To resolve this, move the IPS_CONFIRMED assignment after the table
insertion but before the unlock.
Pablo points out that the confirm-bit-store could be reordered to happen
before hlist add resp. the timeout fixup, so switch to set_bit and
before_atomic memory barrier to prevent this.
It doesn't matter if other CPUs can observe a newly inserted entry right
before the CONFIRMED bit was set:
Such event cannot be distinguished from above "E is the old incarnation"
case: the entry will be skipped.
Also change nf_ct_should_gc() to first check the confirmed bit.
The gc sequence is:
1. Check if entry has expired, if not skip to next entry
2. Obtain a reference to the expired entry.
3. Call nf_ct_should_gc() to double-check step 1.
nf_ct_should_gc() is thus called only for entries that already failed an
expiry check. After this patch, once the confirmed bit check passes
ct->timeout has been altered to reflect the absolute 'best before' date
instead of a relative time. Step 3 will therefore not remove the entry.
Without this change to nf_ct_should_gc() we could still get this sequence:
1. Check if entry has expired.
2. Obtain a reference.
3. Call nf_ct_should_gc() to double-check step 1:
4 - entry is still observed as expired
5 - meanwhile, ct->timeout is corrected to absolute value on other CPU
and confirm bit gets set
6 - confirm bit is seen
7 - valid entry is removed again
First do check 6), then 4) so the gc expiry check always picks up either
confirmed bit unset (entry gets skipped) or expiry re-check failure for
re-inited conntrack objects.
This change cannot be backported to releases before 5.19. Without
commit 8a75a2c174 ("netfilter: conntrack: remove unconfirmed list")
|= IPS_CONFIRMED line cannot be moved without further changes.
Cc: Razvan Cojocaru <rzvncj@gmail.com>
Link: https://lore.kernel.org/netfilter-devel/20250627142758.25664-1-fw@strlen.de/
Link: https://lore.kernel.org/netfilter-devel/4239da15-83ff-4ca4-939d-faef283471bb@gmail.com/
Fixes: 1397af5bfd ("netfilter: conntrack: remove the percpu dying list")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 76179961c423cd698080b5e4d5583cf7f4fcdde9)
[ Upstream commit ae3264a25a4635531264728859dbe9c659fad554 ]
pmc->idev is still used in ip6_mc_clear_src(), so as mld_clear_delrec()
does, the reference should be put after ip6_mc_clear_src() return.
Fixes: 63ed8de4be ("mld: add mc_lock for protecting per-interface mld data")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Link: https://patch.msgid.link/20250714141957.3301871-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit dcbc346f50a009d8b7f4e330f9f2e22d6442fa26)
[ Upstream commit 531d0d32de3e1b6b77a87bd37de0c2c6e17b496a ]
gso_size is expected by the networking stack to be the size of the
payload (thus, not including ethernet/IP/TCP-headers). However, cqe_bcnt
is the full sized frame (including the headers). Dividing cqe_bcnt by
lro_num_seg will then give incorrect results.
For example, running a bpftrace higher up in the TCP-stack
(tcp_event_data_recv), we commonly have gso_size set to 1450 or 1451 even
though in reality the payload was only 1448 bytes.
This can have unintended consequences:
- In tcp_measure_rcv_mss() len will be for example 1450, but. rcv_mss
will be 1448 (because tp->advmss is 1448). Thus, we will always
recompute scaling_ratio each time an LRO-packet is received.
- In tcp_gro_receive(), it will interfere with the decision whether or
not to flush and thus potentially result in less gro'ed packets.
So, we need to discount the protocol headers from cqe_bcnt so we can
actually divide the payload by lro_num_seg to get the real gso_size.
v2:
- Use "(unsigned char *)tcp + tcp->doff * 4 - skb->data)" to compute header-len
(Tariq Toukan <tariqt@nvidia.com>)
- Improve commit-message (Gal Pressman <gal@nvidia.com>)
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Christoph Paasch <cpaasch@openai.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20250715-cpaasch-pf-925-investigate-incorrect-gso_size-on-cx-7-nic-v2-1-e06c3475f3ac@openai.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 6a213143e0eaa5cf115b487fc4b2346806c777ef)
[ Upstream commit 43015955795a619f7ca4ae69b9c0ffc994c82818 ]
For GF variant of WCN6855 without board ID programmed
btusb_generate_qca_nvm_name() will chose wrong NVM
'qca/nvm_usb_00130201.bin' to download.
Fix by choosing right NVM 'qca/nvm_usb_00130201_gf.bin'.
Also simplify NVM choice logic of btusb_generate_qca_nvm_name().
Fixes: d6cba4e6d0 ("Bluetooth: btusb: Add support using different nvm for variant WCN6855 controller")
Signed-off-by: Zijun Hu <zijun.hu@oss.qualcomm.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit ab94e7af363a8116a78bfb95e745a71238bc2f81)
[ Upstream commit 6ef99c917688a8510259e565bd1b168b7146295a ]
This replaces the usage of HCI_ERROR_REMOTE_USER_TERM, which as the name
suggest is to indicate a regular disconnection initiated by an user,
with HCI_ERROR_AUTH_FAILURE to indicate the session has timeout thus any
pairing shall be considered as failed.
Fixes: 1e91c29eb6 ("Bluetooth: Use hci_disconnect for immediate disconnection from SMP")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 4ceefc9c31e74204d0d795b1f26d03c0124ee83d)
[ Upstream commit fe4840df0bdf341f376885271b7680764fe6b34e ]
If a command is received while a bonding is ongoing consider it a
pairing failure so the session is cleanup properly and the device is
disconnected immediately instead of continuing with other commands that
may result in the session to get stuck without ever completing such as
the case bellow:
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Identity Information (0x08) len 16
Identity resolving key[16]: d7e08edef97d3e62cd2331f82d8073b0
> ACL Data RX: Handle 2048 flags 0x02 dlen 21
SMP: Signing Information (0x0a) len 16
Signature key[16]: 1716c536f94e843a9aea8b13ffde477d
Bluetooth: hci0: unexpected SMP command 0x0a from XX:XX:XX:XX:XX:XX
> ACL Data RX: Handle 2048 flags 0x02 dlen 12
SMP: Identity Address Information (0x09) len 7
Address: XX:XX:XX:XX:XX:XX (Intel Corporate)
While accourding to core spec 6.1 the expected order is always BD_ADDR
first first then CSRK:
When using LE legacy pairing, the keys shall be distributed in the
following order:
LTK by the Peripheral
EDIV and Rand by the Peripheral
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
LTK by the Central
EDIV and Rand by the Central
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
When using LE Secure Connections, the keys shall be distributed in the
following order:
IRK by the Peripheral
BD_ADDR by the Peripheral
CSRK by the Peripheral
IRK by the Central
BD_ADDR by the Central
CSRK by the Central
According to the Core 6.1 for commands used for key distribution "Key
Rejected" can be used:
'3.6.1. Key distribution and generation
A device may reject a distributed key by sending the Pairing Failed command
with the reason set to "Key Rejected".
Fixes: b28b494366 ("Bluetooth: Add strict checks for allowed SMP PDUs")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit f3323b18e3cc98225e5a4f9083b0b93174240eab)
[ Upstream commit d85edab911a4c1fcbe3f08336eff5c7feec567d0 ]
Currently, the connectable flag used by the setup of an extended
advertising instance drives whether we require privacy when trying to pass
a random address to the advertising parameters (Own Address).
If privacy is not required, then it automatically falls back to using the
controller's public address. This can cause problems when using controllers
that do not have a public address set, but instead use a static random
address.
e.g. Assume a BLE controller that does not have a public address set.
The controller upon powering is set with a random static address by default
by the kernel.
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6
Address: E4:AF:26:D8:3E:3A (Static)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
Setting non-connectable extended advertisement parameters in bluetoothctl
mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g 1
correctly sets Own address type as Random
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Random (0x01)
Setting connectable extended advertisement parameters in bluetoothctl mgmt
add-ext-adv-params -r 0x801 -x 0x802 -P 2M -g -c 1
mistakenly sets Own address type to Public (which causes to use Public
Address 00:00:00:00:00:00)
< HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036)
plen 25
...
Own address type: Public (0x00)
This causes either the controller to emit an Invalid Parameters error or to
mishandle the advertising.
This patch makes sure that we use the already set static random address
when requesting a connectable extended advertising when we don't require
privacy and our public address is not set (00:00:00:00:00:00).
Fixes: 3fe318ee72 ("Bluetooth: move hci_get_random_address() to hci_sync")
Signed-off-by: Alessandro Gasbarroni <alex.gasbarroni@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 32e624912eed5f87bfe5094e78fe532269b0a451)
[ Upstream commit 3ce58b01ada408b372f15b7c992ed0519840e3cf ]
The function ice_lag_is_switchdev_running() is being called from outside of
the LAG event handler code. This results in the lag->upper_netdev being
NULL sometimes. To avoid a NULL-pointer dereference, there needs to be a
check before it is dereferenced.
Fixes: 776fe19953 ("ice: block default rule setting on LAG interface")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 27591d926191e42b2332e4bad3bcd3a49def393b)
[ Upstream commit 0e9418961f897be59b1fab6e31ae1b09a0bae902 ]
The mentioned test is not very stable when running on top of
debug kernel build. Increase the inter-packet timeout to allow
more slack in such environments.
Fixes: 3327a9c463 ("selftests: add functionals test for UDP GRO")
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/b0370c06ddb3235debf642c17de0284b2cd3c652.1752163107.git.pabeni@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit c18726607c8aa7889c46ba9383df178963a70273)
[ Upstream commit 444020f4bf06fb86805ee7e7ceec0375485fd94d ]
This reverts commit e3eac9f32e ("wifi: cfg80211: Annotate struct
cfg80211_scan_request with __counted_by").
This really has been a completely failed experiment. There were
no actual bugs found, and yet at this point we already have four
"fixes" to it, with nothing to show for but code churn, and it
never even made the code any safer.
In all of the cases that ended up getting "fixed", the structure
is also internally inconsistent after the n_channels setting as
the channel list isn't actually filled yet. You cannot scan with
such a structure, that's just wrong. In mac80211, the struct is
also reused multiple times, so initializing it once is no good.
Some previous "fixes" (e.g. one in brcm80211) are also just setting
n_channels before accessing the array, under the assumption that the
code is correct and the array can be accessed, further showing that
the whole thing is just pointless when the allocation count and use
count are not separate.
If we really wanted to fix it, we'd need to separately track the
number of channels allocated and the number of channels currently
used, but given that no bugs were found despite the numerous syzbot
reports, that'd just be a waste of time.
Remove the __counted_by() annotation. We really should also remove
a number of the n_channels settings that are setting up a structure
that's inconsistent, but that can wait.
Reported-by: syzbot+e834e757bd9b3d3e1251@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=e834e757bd9b3d3e1251
Fixes: e3eac9f32e ("wifi: cfg80211: Annotate struct cfg80211_scan_request with __counted_by")
Link: https://patch.msgid.link/20250714142130.9b0bbb7e1f07.I09112ccde72d445e11348fc2bef68942cb2ffc94@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 167006f73005eb51eab277ef7da7ea5c1d812857)
[ Upstream commit 71257925e83eae1cb6913d65ca71927d2220e6d1 ]
Procedures for nvme-mpath IO accounting:
1) initialize nvme_request and clear flags;
2) set NVME_MPATH_IO_STATS and increase inflight counter when IO
started;
3) check NVME_MPATH_IO_STATS and decrease inflight counter when IO is
done;
However, for the case nvme_fail_nonready_command(), both step 1) and 2)
are skipped, and if old nvme_request set NVME_MPATH_IO_STATS and then
request is reused, step 3) will still be executed, causing inflight I/O
counter to be negative.
Fix the problem by clearing nvme_request in nvme_fail_nonready_command().
Fixes: ea5e5f42cd ("nvme-fabrics: avoid double completions in nvmf_fail_nonready_command")
Reported-by: Yi Zhang <yi.zhang@redhat.com>
Closes: https://lore.kernel.org/all/CAHj4cs_+dauobyYyP805t33WMJVzOWj=7+51p4_j9rA63D9sog@mail.gmail.com/
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit a2f02a87fe211ea57818fb54ff8147d9bc6b5a3b)
[ Upstream commit f0f2b992d8185a0366be951685e08643aae17d6d ]
If a PHY has no driver, the genphy driver is probed/removed directly in
phy_attach/detach. If the PHY's ofnode has an "leds" subnode, then the
LEDs will be (un)registered when probing/removing the genphy driver.
This could occur if the leds are for a non-generic driver that isn't
loaded for whatever reason. Synchronously removing the PHY device in
phy_detach leads to the following deadlock:
rtnl_lock()
ndo_close()
...
phy_detach()
phy_remove()
phy_leds_unregister()
led_classdev_unregister()
led_trigger_set()
netdev_trigger_deactivate()
unregister_netdevice_notifier()
rtnl_lock()
There is a corresponding deadlock on the open/register side of things
(and that one is reported by lockdep), but it requires a race while this
one is deterministic.
Generic PHYs do not support LEDs anyway, so don't bother registering
them.
Fixes: 01e5b728e9 ("net: phy: Add a binding for PHY LEDs")
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Link: https://patch.msgid.link/20250707195803.666097-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit ec158d05eaa91b2809cab65f8068290e3c05ebdd)
[ Upstream commit 80d7762e0a42307ee31b21f090e21349b98c14f6 ]
When inserting a namespace into the controller's namespace list, the
function uses list_add_rcu() when the namespace is inserted in the middle
of the list, but falls back to a regular list_add() when adding at the
head of the list.
This inconsistency could lead to race conditions during concurrent
access, as users might observe a partially updated list. Fix this by
consistently using list_add_rcu() in both code paths to ensure proper
RCU protection throughout the entire function.
Fixes: be647e2c76 ("nvme: use srcu for iterating namespace list")
Signed-off-by: Zheng Qixing <zhengqixing@huawei.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 5d95fbbfaa8fbdd5db73cae1438464e32681158f)
[ Upstream commit 705c79101ccf9edea5a00d761491a03ced314210 ]
A race condition can occur in cifs_oplock_break() leading to a
use-after-free of the cinode structure when unmounting:
cifs_oplock_break()
_cifsFileInfo_put(cfile)
cifsFileInfo_put_final()
cifs_sb_deactive()
[last ref, start releasing sb]
kill_sb()
kill_anon_super()
generic_shutdown_super()
evict_inodes()
dispose_list()
evict()
destroy_inode()
call_rcu(&inode->i_rcu, i_callback)
spin_lock(&cinode->open_file_lock) <- OK
[later] i_callback()
cifs_free_inode()
kmem_cache_free(cinode)
spin_unlock(&cinode->open_file_lock) <- UAF
cifs_done_oplock_break(cinode) <- UAF
The issue occurs when umount has already released its reference to the
superblock. When _cifsFileInfo_put() calls cifs_sb_deactive(), this
releases the last reference, triggering the immediate cleanup of all
inodes under RCU. However, cifs_oplock_break() continues to access the
cinode after this point, resulting in use-after-free.
Fix this by holding an extra reference to the superblock during the
entire oplock break operation. This ensures that the superblock and
its inodes remain valid until the oplock break completes.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220309
Fixes: b98749cac4 ("CIFS: keep FileInfo handle live during oplock break")
Reviewed-by: Paulo Alcantara (Red Hat) <pc@manguebit.org>
Signed-off-by: Wang Zhaolong <wangzhaolong@huaweicloud.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 2baaf5bbab2ac474c4f92c10fcb3310f824db995)
[ Upstream commit 5e28d5a3f774f118896aec17a3a20a9c5c9dfc64 ]
A race condition can occur when 'agg' is modified in qfq_change_agg
(called during qfq_enqueue) while other threads access it
concurrently. For example, qfq_dump_class may trigger a NULL
dereference, and qfq_delete_class may cause a use-after-free.
This patch addresses the issue by:
1. Moved qfq_destroy_class into the critical section.
2. Added sch_tree_lock protection to qfq_dump_class and
qfq_dump_class_stats.
Fixes: 462dbc9101 ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost")
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit fbe48f06e64134dfeafa89ad23387f66ebca3527)
[ Upstream commit 3051247e4faa32a3d90c762a243c2c62dde310db ]
The kobject for the queue, `disk->queue_kobj`, is initialized with a
reference count of 1 via `kobject_init()` in `blk_register_queue()`.
While `kobject_del()` is called during the unregister path to remove
the kobject from sysfs, the initial reference is never released.
Add a call to `kobject_put()` in `blk_unregister_queue()` to properly
decrement the reference count and fix the leak.
Fixes: 2bd85221a6 ("block: untangle request_queue refcounting from sysfs")
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20250711083009.2574432-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit 21033b49cf094ebd9c545ea7b9bed04d084ce84d)
Greg Kroah-Hartman