This encapsulates the APInt creation and worklist management into
a helper function.
To keep one common interface I've use Log2_32 in places that
previously created a mask by subtracting 1 from a power of 2.
Differential Revision: https://reviews.llvm.org/D108324
Let the sext_inreg be selected to sext.w. Remove unneeded sext.w
during PostProcessISelDAG.
This gives opportunities for some other isel patterns to match
like the ADDIPair or matching mul with immediate to shXadd.
This becomes possible after D107658 started selecting W instructions
based on users. The sext.w will be considered a W user so isel
will often select a W instruction for the sext.w input and we can
just remove the sext.w. Otherwise we can combine the sext.w with
a ADD/SUB/MUL/SLLI to create a new W instruction in parallel
to the the original instruction.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D107708
We already do this for non-constants RHS. This just removes the
special case. I believe the special case may have been needed
because the ANY_EXTEND of a constant used to create zero extended
constants, but we recently changed that to produce sign extended
constants.
D107658 is needed to prevent some regressions.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D107697
DAGCombiner::visitStore can clear the upper bits of constants
used by stores. This leads prevents them from being recognized as
sign extended negative values making them more expensive to
materialize.
This patch uses the hasAllNBitUsers method from D107658 to make
a negative constant if none of the users care about the upper bits.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D108052
We normally select these when the root node is a sext_inreg, but
SimplifyDemandedBits can sometimes bypass the sext_inreg for some
users. This can create situation where sext_inreg+add/sub/mul/shl
is selected to a W instruction, and then the add/sub/mul/shl is
separately selected to a non-W instruction with the same inputs.
This patch tries to detect when it would still be ok to use a W
instruction without the sext_inreg by checking the direct users.
This can allow the W instruction to CSE with one created for a
sext_inreg+add/sub/mul/shl. To minimize complexity and cost of
checking, we make no attempt to determine if the CSE will happen
and just always use a W instruction when we can.
Differential Revision: https://reviews.llvm.org/D107658
If we have these instructions, we don't need to hoist the immediate
for an AND that would match them.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D107783
I might be wrong, but I think this is should be width of the known
min size we use for scalable vectors. It shouldn't scale with
minimum vlen.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D107945
For unit-stride and strided load/stores we set the SEW operand of
the pseudo instruction equal the EEW in the opcode. The LMUL
of the pseudo instruction is the LMUL we want.
These instructions calculate EMUL=(EEW/SEW) * LMUL. We can use
this to avoid changing vtype if the SEW/LMUL of the previous
vtype matches the EEW/EMUL ratio we need for the instruction.
Due to how the global analysis works, we can only do this
optimization when the previous vsetvli was produced in the block
containing the store. We need to know in the first phase if the
vsetvli will be inserted so we can propagate information to
the successors in the second phase correctly. This means we can't
depend on predecessors.
Reviewed By: rogfer01
Differential Revision: https://reviews.llvm.org/D106601
Similar for sub except sub isn't commutative.
Modify the existing and/or/xor folds to also work on ISD::SELECT
and not just RISCVISD::SELECT_CC. This is needed to make sure
we do this transform before type legalization turns i32 add/sub
into add/sub+sign_extend_inreg on RV64. If we don't do this before
that, the sign_extend_inreg will still be after the select.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D107603
Shuffles which are broken into separate halves reveal splats in which
a half is accessed via one index; such operations can be optimized to
use "vrgather.vi".
This optimization could be achieved by adding extra patterns to match
`vrgather_vv_vl` which uses a splat as an index operand, but this patch
instead identifies splat earlier. This way, future optimizations can
build on top of the data gathered here, e.g., to splat-gather dominant
indices and insert any leftovers.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D107449
Previously we converted ISD condition codes to integers and stored
them directly in our MIR instructions. The ISD enum kind of belongs
to SelectionDAG so that seems like incorrect layering.
This patch instead uses a CondCode node on RISCV::SELECT_CC until
isel and then converts it from ISD encoding to a RISCV specific value.
This value can be converted to/from the RISCV branch opcodes in the
RISCV namespace.
My larger motivation is to possibly support a microarchitectural
feature of some CPUs where a short forward branch over a single
instruction can be predicated internally. This will require a new
pseudo instruction for select that needs to carry a branch condition
and live probably until RISCVExpandPseudos. At that point it can be
expanded to control flow without other instructions ending up in the
predicated basic block. Using an ISD encoding in RISCVExpandPseudos
doesn't seem like correct layering.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D107400
This is the data to be stored so it should be an input.
To keep operand order similar between loads and stores, move the temp
register to the first dest operand of floating point loads. Rework
the assembler code accordingly.
This doesn't have any functional effect because this Pseudo is only
used by the assembler which doesn't use ins/outs.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D107309
The fcvt fp to integer instructions saturate if their input is
infinity or out of range, but the instructions produce a maximum
integer for nan instead of 0 required for the ISD opcodes.
This means we can use the instructions to do the saturating
conversion, but we'll need to fix up the nan case at the end.
We can probably improve the i8 and i16 default codegen as well,
but I'll leave that for a follow up.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D107230
Use a tail policy operand instead. Inspired by the work in D105092,
but without the intrinsic interface changes.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D106512
Return false from runOnFunction if nothing changed. Curiously
we already returned a bool from detectAndFoldOffset, but didn't
use it.
Fix a couple breaks after returns that I saw while auditing
detectAndFoldOffset.
Differential Revision: https://reviews.llvm.org/D107303
This patch extends the optimization of VID-sequence BUILD_VECTORs
introduced in D104921 to include simple fractional steps composed of a
separated integer numerator and denominator.
A notable limitation in this sequence detection is that only sequences
with steps N/1 or 1/D are found, meaning that the step between elements
and the frequency with which it changes is consistent across the whole
sequence. Fractional steps such as 2/3 won't be matched as those would
involve more complex tracking of state or some level of backtracking.
As is stands, however, this patch is sufficient to match common
interleave-type shuffle indices, for example matching `<0,0,1,1>` (or
commonly `<0,u,1,u>` or `<u,0,u,1>`) to an index sequence divided by 2.
While the optimization is relatively `undef`-tolerant, due to greedy
pattern-matching there even are some simple patterns which confuse the
sequence detection into identifying either a suboptimal sequence or no
sequence at all.
Currently only fractional-step sequences identified as having a
power-of-two denominator are actually lowered to RVV instructions. This
is to avoid introducing divisions into the generated code.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D106533
If a vsetvli instruction is not compatible with the next vector instruction,
and there is no other things that may update or use VL/VTYPE, we could merge
it with the next vsetvli instruction that should be insert for the vector
instruction.
This commit only merge VTYPE with the former vsetvli instruction which has
the same VL.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D106857
This patch aims to improve the performance of BUILD_VECTORs which are
identified as containing a dominant element. Given that most
floating-point constants themselves require a load from the constant
pool, it was possible for the optimization to actually increase the
number of individual loads on small vectors. The exception is the zero
constant -- +0.0 -- which can be materialized efficiently.
While this optimization could do with a proper cost model to weigh the
benfits of a single vector load vs. the manipulation of individual
elements -- even for integer vectors which often require several
instructions to materialize -- without a concrete RVV implementation to
work with any heuristic is likely to be both more obtuse and inaccurate.
Until then, this patch fixes at least one known obvious deficiency.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D106963
The sign_extend we insert here can get turned into a zero_extend if
the sign bit is known zero. This can enable a setcc combine that
shrinks compares with zero_extend. This reduces the use count of
the zero_extend allowing other combines to turn it back into an
any_extend.
This restricts the combine to only cases where the result is used
by a CopyToReg. This works for my original motivating case. I
hope the CopyToReg use will prevent any converted extends from
turning back into an any_extend.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D106754
This patch adds support for lowering the saturating vector add/sub
intrinsics to RVV instructions, for both fixed-length and
scalable-vector forms alike.
Note that some of the DAG combines are still not triggering for the
scalable-vector tests. These require a bit more work in the DAGCombiner
itself.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D106651
I stumbled onto a case where our (sext_inreg (assertzexti32 (fptoui X)), i32)
isel pattern can cause an fcvt.wu and fcvt.lu to be emitted if
the assertzexti32 has an additional user. If we add a one use check
it would just cause a fcvt.lu followed by a sext.w when only need
a fcvt.wu to satisfy both users.
To mitigate this I've added custom isel and new ISD opcodes for
fcvt.wu. This allows us to keep know it started life as a conversion
to i32 without needing to match multiple nodes. ComputeNumSignBits
has been taught that this new nodes produces 33 sign bits. To
prevent regressions when we need to zero extend the result of an
(i32 (fptoui X)), I've added a DAG combine to convert it to an
(i64 (fptoui X)) before type legalization. In most cases this would
happen in InstCombine, but a zero_extend can be created for function
returns or arguments.
To keep everything consistent I've added new nodes for fptosi as well.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D106346
Since we're changing VTYPE, we may change VLMAX which could
invalidate the previous VL. If we can't tell if it is safe we
should use an AVL of 1 instead of keeping the old VL.
This is a quick fix. We may want to thread VL to the pseudo
instruction instead of making up a value. That will require ISD
opcode changes and changes to the C intrinsic interface.
This fixes the issue raised in D106286.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D106403
Lowering certain float vectors without legal vector types could cause a
crash due to a bad interaction between passing floats via GPRs and
argument splitting. Split vector floats appear just like scalar floats.
Under certain situations we choose to pass these float arguments via
GPRs and use an XLenVT location and set the 'BCvt' info to track how
they must be converted back to floating-point values. However, later
logic for handling split arguments may take over, in which case we lose
the previous information and set the 'Indirect' info, thus incorrectly
lowering to integer types.
I don't believe that we would have come across the notion of split
floating-point arguments before. This patch addresses the issue by
updating the lowering so that split arguments are only passed indirectly
when they are scalar integer types.
This has some change to how we lower some larger illegal float vectors,
as can be seen in 'fastcc-float.ll' where the vector is now passed
partly in registers and partly on the stack.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D102852
This relands a6ca88e908 which was originally
reverted due to overflow bugs in e3fa2b1eab.
This patch teaches the compiler to identify a wider variety of
`BUILD_VECTOR`s which form integer arithmetic sequences, and to lower
them to `vid.v` with modifications for non-unit steps and non-zero
addends.
The sequences handled by this optimization must either be monotonically
increasing or decreasing. Consecutive elements holding the same value
indicate a fractional step which, while simple mathematically,
becomes more complex to handle both in the realm of lossy integer
division and in the presence of `undef`s.
For example, a common "interleaving" shuffle index will be lowered by
LLVM to both `<0,u,1,u,2,...>` and `<u,0,u,1,u,...>` `BUILD_VECTOR`
nodes. Either of these would ideally be lowered to `vid.v` shifted right
by 1. Detection of this sequence in presence of general `undef` values
is more complicated, however: `<0,u,u,1,>` could match either
`<0,0,0,1,>` or `<0,0,1,1,>` depending on later values in the sequence.
Both are possible, so backtracking or multiple passes is inevitable.
Sticking to monotonic sequences keeps the logic simpler as it can be
done in one pass. Fractional steps will likely be a separate
optimization in a future patch.
Reviewed By: craig.topper
Differential Revision: https://reviews.llvm.org/D104921
The existing rule about the operand type is strange. Instead, just say
the operand is a TargetConstant with the right width. (Legalization
ignores TargetConstants, so it doesn't matter if that width is legal.)
Highlights:
1. I had to substantially rewrite the AArch64 isel patterns to expect a
TargetConstant. Nothing too exotic, but maybe a little hairy. Maybe
worth considering a target-specific node with some dagcombines instead
of this complicated nest of isel patterns.
2. Our behavior on RV32 for vectors of i64 has changed slightly. In
particular, we correctly preserve the width of the arithmetic through
legalization. This changes the DAG a bit. Maybe room for
improvement here.
3. I explicitly defined the behavior around overflow. This is necessary
to make the DAGCombine transforms legal, and I don't think it causes any
practical issues.
Differential Revision: https://reviews.llvm.org/D105673
If we need to shift left anyway we might be able to take advantage
of LUI implicitly shifting its immediate left by 12 to cover part
of the shift. This allows us to use more bits of the LUI immediate
to avoid an ADDI.
isDesirableToCommuteWithShift now considers compressed instruction
opportunities when deciding if commuting should be allowed.
I believe this is the same or similar to one of the optimizations
from D79492.
Reviewed By: luismarques, arcbbb
Differential Revision: https://reviews.llvm.org/D105417
Replace some existing isel patterns that are covered by the new
code. SLLIUWPat has been removed in favor of folding its root case
into the new code. The other uses in isel patterns for shXadd.uw
have been switched to using hardcoded AND masks.
This is based on the original version of D49585 from ARM. The final
version of that was made a DAG combine, but I've chosen to keep it
as custom isel. I'm not convinced DAG combine is as good with
shift pairs as it is with and+shift. I saw some issues optimizing
the shifts created by vscale lowering if an and isn't created for
from a shift pair.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D106230
I don't think the semantics of the llvm masked gather intrinsic care
about the order the elements are loaded. For example, type legalization
by splitting will chain them in parallel. This is different than
scatter which we do chain in order.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D106025
RISCV would prefer a sign extended constant since that works better
with our constant materialization. We have an existing TLI hook we
use to control sign extension of setcc operands in type legalization.
That hook happens to do the right check we need here, but might be
straying from its original purpose. With only RISCV defining this
hook in tree, I wasn't sure if it was worth adding another hook
with identical behavior.
This is an alternative to D105785 where I tried to handle this in
the RISCV backend by not creating ANY_EXTENDs in some places.
Reviewed By: frasercrmck
Differential Revision: https://reviews.llvm.org/D105918
We assume VLENB is a multiple of 8 and previously relied on shift
pairs being optimized to an AND+SHL/SHR and computeKnownBits
removing the AND. This doesn't happen if (vlenb >> 3) gets CSEd
to have multiple uses. This patch manually emits the best shift
to workaround this.
This adds new pseudoinstructions with ForceTailAgnostic set. This
matches what we did for non-widening VMACC. We should move to a
tail policy operand on the pseudos when we expand the intrinsic
interface to include the tail policy.
If the upper 32 bits are zero and bit 31 is set, we might be able to
use zext.w to fill in the zeros after using an lui and/or addi.
Most of this patch is plumbing the subtarget features into the constant
materialization.
Reviewed By: luismarques
Differential Revision: https://reviews.llvm.org/D105509
Craig Topper